JVC VR 601 Key Lock Operation, Transfer the system setting info of DVR to another

Page 39

Transfer the system setting info of DVR to another:

Insert the SD card which has stored the system setting info into the DVR. Press the Setup button to enter the setup mode and select the SYSTEM.

Highlight SYSTEM and press the Enter button to enter the SYSTEM SETTING page. Then set SD SETUP to LOAD.

MAIN MENU

RECORD

ALARM

CLOCK / TIMER

COMMUNICATION

DISK

SYSTEM

GOTO SYSTEM SETTING

SYSTEM

OPERATION LOG

: ENTER

MENU BACKGND

: 2

BUZZER

: ON

PASSWORD

: SET

SETUP PWD

: OFF

DEFAULT

: LOAD

SD SETUP

 

: SAVE

VERSION

 

: ENTER

MAIN PAGE

 

VIEW OPERATION LOG

 

3.Updating System Software (Please refer to section 3.4 for more details.)

4.6Key Lock Operation

The Key lock operation protects the unit against unauthorized use by disabling the entire front panel controls. Simultaneously press these two “<” and “>” buttons (as shown below) for at least 3 seconds to lock the unit; to release the Key Lock, simultaneously press these two buttons again.

PLAY STOP

PAUSE REC

REV

FWD

Operate Display

Setup

Search

Enter

Monitor

A-rec

T-rec

DISK

OPERATE

11 14

*About the location of the buttons, please refer to Page 10 2.1 Front View.

39

Image 39
Contents Digital Video Recorder Important Safeguards Avertissement Safety Precautions for USA and CanadaConnection to the mains supply Power SystemFor Your Safety Australia Important In the United Kingdom Mains Supply AC 230About the provided power cables for VR-601 U Place of storage and useHandling the unit AC adapter section Important Safety InstructionsTable Of Contents Specifications Compatible Multiplexers Product Introduction Product FeaturesOperate button Front ViewHard-disk drive compartment Hard-disk compartment lockUp / Down buttons Rec IndicatorDisk Indicator Operate IndicatorMobile Rack HDD LED Mobile Rack Power LEDRear View Alarm In/Out This Figure is Looked from the RearNo Connection Basic Connection Connectiong to the AC AdapterMemo Connecting with a Multiplexer Connecting with a Single CameraMultiplexer Connecting with a QuadClock SET Attaching AN External Device to DVRMaxtor Hard-Disk Drive InstallationSystem Information Quality Best Ntsc Rate 6 HRMUX OFF Size POS Updating System Software Standard Configuring Recording SettingsBest HighNtsc MUX OFF PAL MUX OFF Timer Recording Recording OperationsManual Recording Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 WREC Quality Best Audio OFF ALM Type ALM Duration Alarm RecordingPRE- Alarm OFF Main Alarm REC Enable Externally triggered RecordingDiagrams below Search to play back a particular recorded video Operation Status From REC mode to Playback modePlayback Operations Fast Forward/ReverseYou can also operate by using button and button Slow Forward/ReversePlay Back Picture-by-picture Full List Search Search Full List Alarm List Time Search Thumbnail SD CardSearch Operations Play Back Recorded Video from a HDD of the mobile rackSearch Alarm list SearchAlarm List Time SearchThumbnail Search Search Thumbnail Year Full List2003 SD Card Search Alarm Select Main Backup ALL to HD2 Backup OperationsMobile Rack HD Backup Backup Backup Main SET HD2 Usage1220 2001-02-01 0330 2001-03-02 0420 1330 Alarm Select Main Backup Alarm to HD2Disk Setting Reformat HD2 Usage Search buttonArchive Single image Clips into SD Card Security Digital Card SD Card BackupBackup the System setting info into SD Card Save the whole setting into the SD cardKey Lock Operation Transfer the system setting info of DVR to anotherMenu Setup REC Quality REC SettingAlarm Setting REC Quality PRE- Alarm REC Schedule Clock / TimerClock / Timer SET REC Enable OFF Main Timer REC Enable TimerNET Enable OFF NET Dhcp NET IP SET FTP Setting Main NET EnableCommunication REC Mode Comm Setting FTP Setting Comm IDEnable REC Mode Alarm RECPath PasswordFTP Account FTP IP UserBackup Disk SettingBackup Full Main Disk REFORMAT/CLEAR Backup HD HD2 UsageSystem Situation MAC 00 0c 0c 00 00 Bios SW 1.00J Date Jun 9 Setup General Command FormatCommunication Protocol Value of a specific front panel key Description of System State Request Time Second Category=0x02Set Time Second Category=0x02 Request State Second Category=0x06Jumper settings of hard-disk drives for the system Location Mobile Rack InstallationPage Push the active-handle inward Lock the Key System Default SET RS232 / RS485 Disk Setting ReformatD Message Meanings PIN no Network ViewerPage View the VR-601 video from a remote PC Function Buttons Description Viewing images View all the connected devicesView single device Playback function bar Set the record timer Change the Record & Timer Properties Via the NetworkSet the regular record settings Set the Alarm record settingsArchive Images to the Computer Image Viewer Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Connect to a LAN Hub Intranet Physical specification of RJ-45 cable for EthernetCable Connections Connect to a computerConnect to WAN Internet RJ-45 PIN configuration for LAN HubConfigure Your DVR Network Settings Enable DVR Network FunctionSet IP Address Enable Dhcp Function12.3 TCP/IP Communication Software Page 12.4 TCP/IP installation 12.5 TCP/IP Configuration settingClick Start Settings Control Panel Network Click Start Programs MS-DOS Prompt Connection TestingPage Model Number VR-601 U VR-601 E Design and specifications subject to change without noticeDVR Viewer Manufacturer Model ChannelColors Decode on