Honeywell W7761A specifications Software version

Page 60

EXCEL 10 W7761A INPUT/OUTPUT DEVICE

Table C3. Status Points (Right Continued).

	Share (SH), Map (MA), Direct Access (DA)
	E-Vision (EV): Calibrate (C), Monitor (M),
			Parameter (P), Schematic (S)
		Hardware Configuration (HW),
			Manual Point (MN), Test (TS)

SH		MA		DA	EV	HW	MN		TS	Comments

				X	M					ResSensor2Error(AI2): Refer to the description of ResSensor1Error(AI1).

				X	M					ResSensor3Error(AI3): Refer to the description of ResSensor1Error(AI1).

				X	M					ResSensor4Error(AI4): Refer to the description of ResSensor1Error(AI1).

				X						Software version.

										A four byte ASCII string indicating the type of node (model).

				X						Software version.

				X						Software version.

										The NodeType is a numeric identifier that is stored in EPROM that identifies the
										Excel 10 node type. Whenever a new software version or upgrade is issued, this is
										reflected in nroPgmVer which typically is read by a network management node to
										identify the node type. The contents of nroPgmVer contain compatible model type
										information and is fixed at the time when the node software is compiled.

										CommFailure:
										This field is not supported and is set to 0 (FALSE).

										disabled: disabled reports 1 if nvoIO mode is set to DISABLED_MODE or
										FACTORY_TEST mode. Otherwise disabled is set to 0.

										ElectricalFault:
										This field is not supported and is set to 0 (FALSE).

										FailSelfTest:
										This field is not supported and is set to 0 (FALSE).

										FeedbackFailure:
										This field is not supported and is set to 0 (FALSE).

										InAlarm: If there are currently any active alarms reported by InAlarm, or InAlarm is
										set to AlarmNotifyDisabled, then InAlarm is set to True, if not InAlarm is set to False.

										InvalidId: If object_id is not a valid object, invalid_id is set to 1 (TRUE) otherwise it is
										set to 0 (FALSE).

										InvalidRequest: If object_request is not a valid request for the object addressed,
										InvalidRequest is set to 1 (TRUE) otherwise it is set to 0 (FALSE).

										(continued)

60

74-2699

Image 60

Contents Excel 10 W7761A Remote Input/Output Device List of Tables AppendicesDescription of Devices Typical system overviewControl Application Control ProvidedProducts Covered Organization of ManualProduct Names Agency Listings Abbreviations and DefinitionsExcel 10 W7761A INPUT/OUTPUT Device Construction ControllersExcel 10 W7761A Remote I/O Device W7761A construction in in. mm Performance Specifications Power List Of Available Points W7761ASpecified Space Temperature Sensing Range Environmental Operating TemperatureShipping Temperature Memory CapacityDischarge Air Temperature Outdoor Air TemperatureReturn Air Temperature Mixed Air TemperatureWall Modules 5585Configurations T7780 construction, subbase dimensions in in. mmMixed-Output-Type Control Occupancy SensorWindow Open/Closed Digital Input Wall Module OptionsOverview Plan The SystemApplication Steps Step No Description Lay Out Communications and Power Wiring Determine Other Bus Devices RequiredBus Layout 750,1$ Power Wiring Power Budget Calculation ExampleVA Ratings For Transformer Sizing Device Description Line LossVA Rating Nema class 2 transformer voltage output limitsLine VOLTAGE` GREATER` Than 150 VAC Prepare Wiring Diagrams General ConsiderationsW7761A Devices W7761A I/O Description Terminal Number DescriptionTemperature Sensor DE V IC E Window Contact Contact Closed = Occupancy Sensor Occupied Valve Actuator Bus Termination Module Typical Pneumatic transducer Series 60 Floating to W7761ASee for E-Bus termination wiring options +$672 Order Equipment Excel 10 W7750 ControllersT7770 Wall Modules SensorsAccessories Echelon Based Components and PartsCabling Temperature Degrees Broadcasting the Service Message Excel 10 AlarmsW7761A Device Status LED T7780 Ddwm Bypass Pushbutton LED StatesAppendix A. Using E-Vision to Commission a W7761 Device Adding Analog Inputs Enthalpy 4 to 20 mAAdding Other VOLTAGE/CURRENT Sensors Adding Digital Inputs Room Temperature Sensor RmTemp Appendix B. Sequences of OperationCommon Operations Window Sensor StatusWndw Dirty Filter MonitorSeries 60 Modulating Control Pulse Width Modulating PWM ControlTemperature Relative Humidity RelativeAir Flow CO 2 ConcentrationDefault Table C1. Input/Output Points LeftTable C1. Input/Output Points Right Excel 10 W7761A INPUT/OUTPUT Device Values that can be assigned to any output channels English Metric or User Address DI3Sel1Type Refer to the description for DI1Sel1Type Stoff Stnul Stlow Stmed Sthigh Ston DO2Type Excel 10 W7761A INPUT/OUTPUT Device SrcDigIn2Sts Refer to the description for SrcDigIn1Sts Table C2. Control Parameters Left Table C2. Control Parameters Right SH MA DA EV HW MN TSNoalarm Table C3. Status Points LeftTable C3. Status Points Right RIO1 Software version NvoStatus InOverride SH MA DA EV HW MN TS Table C4. Configuration Parameters Left Table C4. Configuration Parameters Right DO0 Higher than the value specified for AILowLimit DO4 Seconds = 25.6 seconds DO6PWMPeriod Refer to the description for DO1PWMPeriod Table C5. Direct Access And Special Points Left Table C5. Direct Access And Special Points RightApproximate Memory Size Estimating Procedure Fig. D-1. Point capacity estimate for Zone ManagerAppendix E. Sensor Data for Calibration Resistance SensorsSensor Type Sensor Use1956.79 Voltage/Current Sensors Table E-4. Sensor Voltage Versus HumidityHumidity Percentage Sensor Voltage C7600C1008 4 to 20 mA C7600C output current vs. humidity Sensor Type Fig. E-6. Graph of Sensor Current versus Enthalpy volts Table E-9. Sensor Voltage Versus CO 2 Concentration CO 2 Concentration PPM Sensor VoltageTable E-10. Sensor Voltage Versus Input Voltage To A/D Voltage to A/D Sensor Voltage Table E-11. Sensor Voltage Vdc Versus Pressure InwPressure Inw kPa Sensor Voltage Vdc 3ODD