DTS RV4700 DTS-ES manual Remote Control Operation Range, Loading Batteries

Page 12

OPERATING COMPONENTS WITH REMOTE CONTROL

Enter the setup code of the components

1 respectively, referring to “ENTERING A SETUP CODE”(page14).

Turn on the components you want to

2 operate.

Press the DEVICE button on the remote

3 control corresponding to the component you want to operate.

Press the button corresponding to the

4 operation you want while aiming the remote control at the REMOTE SENSOR on the component.

When a button is pressed, the corresponding DEVICE button flickers.

However, in case of DVD player, aim it at the REMOTE SENSOR on the corresponding component.

REMOTE CONTROL OPERATION RANGE

Use the remote control within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor.

7m

30

30

VOL. CH LEVEL

HOME THEATER MASTER

RV4700 DTS-ES

LOADING BATTERIES

When this remote control does not operate the component, the old batteries should be replaced.

If the batteries are removed for a longer period of time, the remote control might lose its memory and require reentering.

Remove the cover.

1

2

Load four batteries(“AAA” size, 1.5 V)

matching the polarity.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

Image 12
Contents RV4700 DTS-ES Unpacking and Installation IntroductionRead this Before Operating Your Unit AC Voltage SelectionContents Connecting Antennas Connecting Audio Components Connecting 7.1CH Direct INPUTsSystem Connections Connecting Video Components Front SUR Round BackConnecting MULTI-ROOM System KIT Connecting Digital INs and OUTPRE OUT connections Switched AC Outlet AC Inlet Connecting SpeakersRoom 2 connections Front Panel Controls Fluorescent DisplayUniversal Remote Controls LED Lamp Device ButtonsFunction Table of the Numbered Buttons Remote Control Operation Range Loading BatteriesAdditional Information on Remote Command Codes Functions CodesEntering a Setup Code For Power ON/OFFWhen selecting the 7.1 CH Direct as desired OperationsBefore operation Tape Monitor functionWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSound tracks Surround Sound Surround modesTheater MovieHall 1/2 StadiumSpeaker placement Front left and right speakers and center speakerSurround left and right speakers Surround back left and right speakersSelected decoding mode as follows Enjoying Surround SoundWhen canceling the surround mode for normal stereo operation Adjusting each channel level Select the desired channelDownmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceAdditional Function for RV4700 DTS-ES RDS Tuner Only Listening to RDS Broadcastsfm onlyEON PTY EON Enhanced Other Networks InformationDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Using the OSD OSD Menu SettingsWhen selecting the desired input source Current Status DisplayWhen selecting the Speaker Setup When selecting the Surround SetupWhen selecting the Function Select When selecting the CH Level TrimSetting the Speaker Setup When selecting the Speaker ConfigWhen selecting the Speaker Distance When selecting the LFE Level Control Setting the Function Select When selecting the Input SetupWhen selecting the Digital in Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications RV4700 DTS-ES