DTS RV4700 DTS-ES Speaker placement, Front left and right speakers and center speaker, Subwoofer

Page 20

Speaker placement

Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of speaker placement and recommendations are as follows :

Front left and right speakers and center speaker

Place the front speakers with their front surfaces as flush with TV or monitor screen as possible.

Place the center speaker between the front left and right speakers and no further from the listening position than the front speakers.

Place each speaker so that sound is aimed at the location of the listener’s ears when at the listening position.

Surround left and right speakers

Place the surround speakers approximately 1 meter (40 inches) above the ear level of a seated listener on the direct left and right of them or slightly behind.

Surround back left and right speakers.

Place the surround back speakers at the back facing the front at a narrower distance than the front speakers.

When using a single surround back speaker, place it at the rear center facing the front at a slightly higher position (0 to 20 cm) than the surround speakers.

We recommend installing the surround back speaker(s) at a slightly downward facing angle. This effectively prevents the surround back channel signals from reflecting off the TV or screen at the front center, resulting in interference and making the sense of movement from the front to the back less sharp.

1.

TV or screen

7.

Surround right speaker

2.

Front left speaker

8.

Surround back left speaker

3.

Subwoofer

9.

Surround back right speaker

4.

Center speaker

10.

Surround back center speaker

5.

Front right speaker

11.

Listeing position

6.

Surround left speaker

 

 

Subwoofer

The subwoofer reproduces powerful deep bass sounds. Place a powered subwoofer anywhere in the front as desired.

Notes :

When using a conventional TV , to avoid interference with the TV picture, use only magnetically shielded front left and right speakers and center speaker.

To obtain the best surround effects, the speakers except the subwoofer should be full range speakers.

Surround speaker

Surround back

 

speaker

 

Point slightly

Front speaker

downward

 

 

60 to 90 cm

20

Image 20
Contents RV4700 DTS-ES Unpacking and Installation IntroductionRead this Before Operating Your Unit AC Voltage SelectionContents System Connections Connecting Antennas Connecting Audio ComponentsConnecting 7.1CH Direct INPUTs Connecting Video Components Front SUR Round BackPRE OUT connections Connecting MULTI-ROOM System KITConnecting Digital INs and OUT Room 2 connections Switched AC OutletAC Inlet Connecting Speakers Front Panel Controls Fluorescent DisplayUniversal Remote Controls LED Lamp Device ButtonsFunction Table of the Numbered Buttons Remote Control Operation Range Loading BatteriesAdditional Information on Remote Command Codes Functions CodesEntering a Setup Code For Power ON/OFFWhen selecting the 7.1 CH Direct as desired OperationsBefore operation Tape Monitor functionWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSound tracks Surround Sound Surround modesTheater MovieHall 1/2 StadiumSpeaker placement Front left and right speakers and center speakerSurround left and right speakers Surround back left and right speakersSelected decoding mode as follows Enjoying Surround SoundWhen canceling the surround mode for normal stereo operation Adjusting each channel level Select the desired channelDownmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceAdditional Function for RV4700 DTS-ES RDS Tuner Only Listening to RDS Broadcastsfm onlyEON PTY EON Enhanced Other Networks InformationDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Using the OSD OSD Menu SettingsWhen selecting the desired input source Current Status DisplayWhen selecting the Speaker Setup When selecting the Surround SetupWhen selecting the Function Select When selecting the CH Level TrimSetting the Speaker Setup When selecting the Speaker ConfigWhen selecting the Speaker Distance When selecting the LFE Level Control When selecting the Digital in Setup Setting the Function SelectWhen selecting the Input Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications RV4700 DTS-ES