DTS RV4700 DTS-ES manual Select the desired channel, Adjusting each channel level

Page 23

Adjusting each channel level

 

4

Adjust the level of the selected channel

 

as desired.

• If you have performed the CH LEVEL TRIM

procedure on the OSD menu, you need not to do this

 

 

procedure. (For details, refer to “SETTING THE CH

 

 

LEVEL TRIM” on page 45.)

 

 

MULTI CONTROL

Select the desired channel.

 

 

CH LEVEL

 

 

or

3

 

 

 

 

 

 

 

DOWN

UP

CHANNEL

CH SEL

 

 

SELECTOR

 

 

 

or

 

• If the channel display disappears, start from the above

 

 

 

 

step

again.

• Each time this button is pressed, the corresponding

 

 

 

 

 

 

 

 

 

channel is selected and displayed for 3 seconds as

 

 

 

 

 

follows:

5

Repeat the above steps

and

to

 

 

FRONT-L CENTER(or FRONT-C) FRONT-R SURR-R

 

 

adjust each channel level until the sound

 

 

 

 

 

 

SUBWOOFER SURR-L (( SURR-C) or ( BACK-L BACK-R))

 

level of each speaker is heard to be

 

 

 

 

 

 

 

 

 

equally loud.

 

 

•According to the speaker setting( None or No), center, surround, surround back or subwoofer channel will not be selected.

Adjusting each channel level with test tone

7

At each channel, adjust the level as desired

• Only when playing a program source in available

until the sound level of each speaker is

heard to be equally loud.

 

surround modes except the DOLBY VIRTUAL

 

 

 

 

mode, the volume level of each channel can be

 

 

 

 

adjusted easily with the test tone function.

MULTI CONTROL

 

 

Note : When the 7.1 CH DIRECT is selected as an

 

 

 

 

input source, the test tone function does not

 

 

 

CH LEVEL

work.

 

 

or

 

 

Enter the test tone mode.

DOWN

UP

 

 

6

 

 

 

 

 

 

 

 

 

 

• You can select the desired channel and adjust its level

TEST TONE

 

with repeating the steps

and

in “Adjusting each

 

 

 

or

channel level” procedure.

 

 

 

 

 

 

 

 

TEST

 

 

 

 

 

TONE

 

 

 

 

 

 

8

Cancel the test tone function.

• The test tone will be heard from the speaker of each

 

 

 

 

 

 

 

channel for 2 seconds as follows:

 

 

 

 

Front Left Center

Front Right Surround Right

 

TEST TONE

 

 

Surround Left ((

Surround Center) or ( Back Left Back Right))

 

or

 

 

SUBwoofer

 

 

 

 

 

 

 

 

TEST

 

 

 

 

 

TONE

According to the speaker setting (None or No), the test tone of the corresponding channel is not available.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents RV4700 DTS-ES Introduction Unpacking and InstallationAC Voltage Selection Read this Before Operating Your UnitContents System Connections Connecting Antennas Connecting Audio ComponentsConnecting 7.1CH Direct INPUTs Front SUR Round Back Connecting Video ComponentsPRE OUT connections Connecting MULTI-ROOM System KITConnecting Digital INs and OUT Room 2 connections Switched AC OutletAC Inlet Connecting Speakers Fluorescent Display Front Panel ControlsLED Lamp Device Buttons Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Remote Control Operation RangeFunctions Codes Additional Information on Remote Command CodesFor Power ON/OFF Entering a Setup CodeTape Monitor function When selecting the 7.1 CH Direct as desiredOperations Before operationAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSound tracks Surround modes Surround SoundStadium TheaterMovie Hall 1/2Surround back left and right speakers Speaker placementFront left and right speakers and center speaker Surround left and right speakersEnjoying Surround Sound Selected decoding mode as followsWhen canceling the surround mode for normal stereo operation Select the desired channel Adjusting each channel levelDownmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsListening to RDS Broadcastsfm only Additional Function for RV4700 DTS-ES RDS Tuner OnlyInformation EON PTY EON Enhanced Other NetworksDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorDigital Audio Recording with MD Recorder Compressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the desired input sourceWhen selecting the CH Level Trim When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the Function SelectWhen selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance When selecting the LFE Level Control When selecting the Digital in Setup Setting the Function SelectWhen selecting the Input Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Function Select for RoomProblem Possible Cause Remedy Troubleshooting GuideSpecifications RV4700 DTS-ES
Top Page Image Contents