DTS RV4700 DTS-ES manual When selecting the Tone Control

Page 41

When selecting the TONE CONTROL

Press the CURSOR UP( )/DOWN( ) buttons to select the TONE CONTROL, then press the ENTER

1 button.

VOL. CH LEVEL

ENTER

T O N E C O N T R O L

 

 

T O N E

D E F E A T

:

Off

 

B A S S

----- + -----

0

dB

T R E B L E ----- + -----

0

dB

HOME THEATER MASTER

RV4700 DTS-ES

R E T U R N : B a c k

, : S e l e c t

Note:

• When the source direct function is activated, the TONE CONTROL cannot be selected.

Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired tone defeat mode.

2

VOL. CH LEVEL

Each time these buttons are pressed, the tone defeat mode changes as follows:

On : Select this when listening to a program source without the tone effect.

Off : Select this when adjusting tone for your taste.

HOME THEATER MASTER

RV4700 DTS-ES

Note:

When the tone defeat mode is set to On, the tone (bass and treble) cannot be adjusted.

 

When the tone defeat mode is set to Off to adjust the tone (bass and treble)

1.

Press the CURSOR UP( )/DOWN( ) buttons to select the desired tone mode.

 

• Each time these buttons are pressed, “ ” is moved to the tone defeat mode or the corresponding tone mode.

2.

At the desired tone mode, press the CURSOR LEFT( )/RIGHT( ) buttons to adjust the selected tone as desired.

The tone level can be adjusted within the range of -10~+10 dB.

In general, we recommend the bass and treble to be adjusted to 0 dB(flat level).

Extreme settings at high volume may damage your speakers.

3.To complete tone adjustment, repeat the above steps 1 and 2.

41

Image 41
Contents RV4700 DTS-ES Introduction Unpacking and InstallationAC Voltage Selection Read this Before Operating Your UnitContents System Connections Connecting Antennas Connecting Audio ComponentsConnecting 7.1CH Direct INPUTs Front SUR Round Back Connecting Video ComponentsPRE OUT connections Connecting MULTI-ROOM System KITConnecting Digital INs and OUT Room 2 connections Switched AC OutletAC Inlet Connecting Speakers Fluorescent Display Front Panel ControlsLED Lamp Device Buttons Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Remote Control Operation RangeFunctions Codes Additional Information on Remote Command CodesFor Power ON/OFF Entering a Setup CodeOperations When selecting the 7.1 CH Direct as desiredBefore operation Tape Monitor functionAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSound tracks Surround modes Surround SoundMovie TheaterHall 1/2 StadiumFront left and right speakers and center speaker Speaker placementSurround left and right speakers Surround back left and right speakersEnjoying Surround Sound Selected decoding mode as followsWhen canceling the surround mode for normal stereo operation Select the desired channel Adjusting each channel levelDownmixing into 2 front channels Manual tuning Auto tuningPresetting radio stations Listening to Radio BroadcastsScanning preset stations in sequence Tuning to preset stationsListening to RDS Broadcastsfm only Additional Function for RV4700 DTS-ES RDS Tuner OnlyInformation EON PTY EON Enhanced Other NetworksRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Adjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Compressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback OSD Menu Settings Using the OSDWhen selecting the desired input source Current Status DisplayWhen selecting the Surround Setup When selecting the Speaker SetupWhen selecting the Function Select When selecting the CH Level TrimWhen selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance When selecting the LFE Level Control When selecting the Digital in Setup Setting the Function SelectWhen selecting the Input Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Function Select for RoomProblem Possible Cause Remedy Troubleshooting GuideSpecifications RV4700 DTS-ES