DTS RV4700 DTS-ES manual Enjoying Surround Sound, Selected decoding mode as follows

Page 21

ENJOYING SURROUND SOUND

•Surround sound effect will not work properly if the signal passes through a graphic equalizer.

Please refer to your equalizer operating instructions for guidance on switching off (or defeating) the equalizer.

Note : Before surround playback, first perform the SPEAKER SETUP procedure, etc. on the OSD menu for optimum performance.(For detais, refer to “SETTING THE SPEAKER SETUP” on page 36.)

Depending on the input digital signal format, select the desired decoding mode.

1

•Each time this button is pressed, the decoding mode changes as follows :

DECODING

VOL. CH LEVEL

or

AUTO

HOME THEATER MASTER

RV4700 DTS-ES

*Auto mode(“ AUTO” lights up) : The input digital signal format (DTS, Dolby Digital, MPEG or PCM ( 2 channel stereo), etc.) used by the selected digital input source is detected automatically to perform the necessary decoding process for optimum surround modes.

*Dolby Digital mode(“DOLBY DIGITAL” lights up) : The Dolby Digital signals processing is performed only when Dolby Digital signals are input.

*DTS mode(“ DTS” lights up) : The DTS signal processing is performed only when DTS signals are input.

*MPEG mode(“MPEG” lights up) : The MPEG signal processing is performed only when MPEG signals are input.

*PCM mode(“PCM” lights up) : The PCM signal processing is performed only when PCM signals are input.

Notes :

•Only when the digital input is selected as signal input for the input sources except TUNER and AUX, the decoding mode can be selected.

•Noise may be generated at the beginning of playback and while searching during DTS playback in the auto mode. In this case, try playing in the DTS mode.

Select the desired surround mode.

2

MULTI CONTROL

 

VOL. CH LEVEL

 

or

• Each time the MULTI CONTROL knob on the front is rotated or

 

the DSP MODE button on the remote control is pressed, the

HOME THEATER MASTER

surround mode changes depending on the input signal format and

RV4700 DTS-ES

 

the selected decoding mode as follows:

 

DSP

MODE

* When Dolby Digital signals are input in the auto or Dolby Digital mode, the following modes can be selected.

DOLBY DIGITAL ( DOLBY PRO LOGIC II MOVIE DOLBY PRO LOGIC II MUSIC DOLBY PRO LOGIC) DOLBY VIRTUAL

Only when Dolby Digital 2.0 channel signals are input, the surround modes in ( ) can be selected, too.

* When PCM (2 channel stereo) signals are input in the auto or PCM mode, the following modes can be selected.

DOLBY PRO LOGIC II MOVIE

DOLBY PRO LOGIC II MUSIC

DOLBY PRO LOGIC DOLBY VIRTUAL DTS NEO MOVIE DTS NEO MUSIC

 

 

MATRIX GAME ARENA 2

ARENA 1 CLUB 2 CLUB 1

CHURCH STADIUM HALL 2 HALL 1 MOVIE THEATER

 

 

 

 

•When the analog input is selected as signal input and analog stereo signals are input, you can select the desired of these above surround modes, too.

•However, when DTS or MPEG signals are input in the following decoding modes, the corresponding surround mode will be automatically selected regardless of using the MULTI CONTROL knob or DSP MODE button:

*When DTS signals are input in the auto or DTS mode, the corresponding DTS mode will be selected.

*When MPEG signals are input in the auto or MPEG mode, MPEG mode will be selected.

Notes:

•When the selected decoding mode is not matched to the input signal format, the indicator of the signal being input is flickering, meaning the required process cannot be performed and no sound is heard. Therefore, be sure to select the required decoding mode and the available surround mode according to the input signal format.

•When the 7.1 CH DIRECT is selected as an input source, the surround mode cannot be selected.

•When the source direct function is activated, the decoding mode and surround mode cannot be selected.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents RV4700 DTS-ES Introduction Unpacking and InstallationAC Voltage Selection Read this Before Operating Your UnitContents Connecting Antennas Connecting Audio Components Connecting 7.1CH Direct INPUTsSystem Connections Front SUR Round Back Connecting Video ComponentsConnecting MULTI-ROOM System KIT Connecting Digital INs and OUTPRE OUT connections Switched AC Outlet AC Inlet Connecting SpeakersRoom 2 connections Fluorescent Display Front Panel ControlsLED Lamp Device Buttons Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Remote Control Operation RangeFunctions Codes Additional Information on Remote Command CodesFor Power ON/OFF Entering a Setup CodeOperations When selecting the 7.1 CH Direct as desiredBefore operation Tape Monitor functionAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSound tracks Surround modes Surround SoundMovie TheaterHall 1/2 StadiumFront left and right speakers and center speaker Speaker placementSurround left and right speakers Surround back left and right speakersEnjoying Surround Sound Selected decoding mode as followsWhen canceling the surround mode for normal stereo operation Select the desired channel Adjusting each channel levelDownmixing into 2 front channels Manual tuning Auto tuningPresetting radio stations Listening to Radio BroadcastsScanning preset stations in sequence Tuning to preset stationsListening to RDS Broadcastsfm only Additional Function for RV4700 DTS-ES RDS Tuner OnlyInformation EON PTY EON Enhanced Other NetworksRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Adjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Compressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback OSD Menu Settings Using the OSDWhen selecting the desired input source Current Status DisplayWhen selecting the Surround Setup When selecting the Speaker SetupWhen selecting the Function Select When selecting the CH Level TrimWhen selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance When selecting the LFE Level Control Setting the Function Select When selecting the Input SetupWhen selecting the Digital in Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Function Select for RoomProblem Possible Cause Remedy Troubleshooting GuideSpecifications RV4700 DTS-ES
Top Page Image Contents