DTS RV4700 DTS-ES manual Entering a Setup Code, For Power ON/OFF

Page 14

ENTERING A SETUP CODE

•This remote control can control up to eight different components.

•Before operating audio and video components using the remote control supplied with this receiver, the setup code for each component should be entered.

1

Turn on the component you want to control.

2

Find the setup code for your component

 

 

 

 

referring to “Set-Up Code Table” in the

 

 

 

 

operating manual of this remote control.

Example) When entering the setup code for this

Example) The correct setup code for this receiver is

 

receiver, turn on this receiver.

 

 

“001”.

 

 

 

 

3

Press the corresponding DEVICE and the

4

Enter the 3 digit setup code aiming the

MUTE buttons simultaneously.

 

remote control at the REMOTE SENSOR

 

 

 

 

on the component.

 

 

For receiver or amplifier :

 

 

For

"001" :

0

0

1

 

 

For CD player

:

 

 

 

 

 

 

 

 

 

 

 

 

 

For

"102" :

1

0

2

 

 

For CABLE

:

 

 

 

 

 

 

 

 

 

 

 

 

 

• Your component will be turned off when the correct

 

 

 

 

 

setup code is entered.

 

 

 

• Then the LED lamp and the corresponding DEVICE

• Continue to enter the corresponding codes until your

button on the remote control light up for 20 seconds.

component turns off.

 

 

 

 

 

 

 

 

• If the LED lamp and the corresponding DEVICE

 

 

 

 

 

button go off, start from the step

again.

5

Press the corresponding DEVICE button to

6

Operate the component using the

store the setup code.

 

 

corresponding function buttons on the

 

 

 

 

remote control such as POWER, CH /

 

 

 

 

 

 

and VOL /

 

buttons, etc.

 

For receiver or amplifier :

 

 

• If any of the buttons do not perform as they should start

 

 

 

 

 

 

For CD player

:

 

 

from step

again to enter the next setup code.

 

 

 

 

 

Notes:

 

 

 

 

 

 

For CABLE

:

 

 

• Some audio and video components have separate buttons

 

 

 

for POWER ON/OFF.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In this case, press the corresponding DEVICE button to

 

 

 

 

 

turn the component ON and press the POWER button to

• Then the LED lamp and the corresponding DEVICE

turn the component OFF.

 

 

 

• If there is no correct setup code or if the

button will flicker twice.

 

 

 

 

Manufacturer/Brand for your component is not listed in

 

 

 

 

 

 

 

 

 

 

“Set-Up Code Table” in the operating manual of this

7

Repeat the above steps

to

for each

remote control, please use the “Auto Search Method” on

page 10 in the operating manual of this remote control.

of your other components.

 

 

 

 

• Although each setup code is designed to work with many

 

 

 

 

 

different modes, certain codes may not work with some

 

 

 

 

 

models. (Also, certain codes may only operate some of

 

 

 

 

 

the functions available on a given model.)

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents RV4700 DTS-ES Unpacking and Installation IntroductionRead this Before Operating Your Unit AC Voltage SelectionContents System Connections Connecting Antennas Connecting Audio ComponentsConnecting 7.1CH Direct INPUTs Connecting Video Components Front SUR Round BackPRE OUT connections Connecting MULTI-ROOM System KITConnecting Digital INs and OUT Room 2 connections Switched AC OutletAC Inlet Connecting Speakers Front Panel Controls Fluorescent DisplayUniversal Remote Controls LED Lamp Device ButtonsFunction Table of the Numbered Buttons Remote Control Operation Range Loading BatteriesAdditional Information on Remote Command Codes Functions CodesEntering a Setup Code For Power ON/OFFBefore operation When selecting the 7.1 CH Direct as desiredOperations Tape Monitor functionWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSound tracks Surround Sound Surround modesHall 1/2 TheaterMovie StadiumSurround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back left and right speakersSelected decoding mode as follows Enjoying Surround SoundWhen canceling the surround mode for normal stereo operation Adjusting each channel level Select the desired channelDownmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceAdditional Function for RV4700 DTS-ES RDS Tuner Only Listening to RDS Broadcastsfm onlyEON PTY EON Enhanced Other Networks InformationRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback When selecting the desired input source Using the OSDOSD Menu Settings Current Status DisplayWhen selecting the Function Select When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the CH Level TrimSetting the Speaker Setup When selecting the Speaker ConfigWhen selecting the Speaker Distance When selecting the LFE Level Control When selecting the Digital in Setup Setting the Function SelectWhen selecting the Input Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications RV4700 DTS-ES
Top Page Image Contents