DTS RV4700 DTS-ES manual When selecting the LFE Level Control

Page 38

When selecting the LFE LEVEL CONTROL

Press the CURSOR UP( )/DOWN( ) buttons to select the LFE LEVEL CONTROL, then press the

1 ENTER button.

ENTER

L F E L E V E L C O N T R O L
D O L B Y	----- +	0	dB
D T S	----- + -----	0	dB
M P E G ----- + -----		0	dB

R E T U R N : B a c k, : S e l e c t

Press the CURSOR UP( )/DOWN( ) buttons to select the desired LFE level mode.

2

• Each time these buttons are pressed, “ ” is moved to the corresponding LFE level mode.

Press the CURSOR LEFT( )/RIGHT( ) buttons to adjust the selected LFE level as desired.

3

• Each time these buttons are pressed, the LFE level can be adjusted within the range of either -10~0 dB for Dolby Digital program sources or -10~+10 dB for DTS and MPEG program sources.

• In general, we recommend the LFE level for Dolby Digital program sources to be set at 0 dB and at +10 dB for DTS program sources.(However, the recommended LFE level for some early DTS program sources is 0 dB.) If the recommended levels seem too high, lower the setting as necessary.

Repeat the above steps

and

until each level is adjusted as desired.

4

38

Image 38

Contents RV4700 DTS-ES Unpacking and Installation IntroductionRead this Before Operating Your Unit AC Voltage SelectionContents System Connections Connecting Antennas Connecting Audio ComponentsConnecting 7.1CH Direct INPUTs Connecting Video Components Front SUR Round BackPRE OUT connections Connecting MULTI-ROOM System KITConnecting Digital INs and OUT Room 2 connections Switched AC OutletAC Inlet Connecting Speakers Front Panel Controls Fluorescent DisplayUniversal Remote Controls LED Lamp Device ButtonsFunction Table of the Numbered Buttons Remote Control Operation Range Loading BatteriesAdditional Information on Remote Command Codes Functions CodesEntering a Setup Code For Power ON/OFFBefore operation When selecting the 7.1 CH Direct as desiredOperations Tape Monitor functionWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSound tracks Surround Sound Surround modesHall 1/2 TheaterMovie StadiumSurround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back left and right speakersSelected decoding mode as follows Enjoying Surround SoundWhen canceling the surround mode for normal stereo operation Adjusting each channel level Select the desired channelDownmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceAdditional Function for RV4700 DTS-ES RDS Tuner Only Listening to RDS Broadcastsfm onlyEON PTY EON Enhanced Other Networks InformationRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback When selecting the desired input source Using the OSDOSD Menu Settings Current Status DisplayWhen selecting the Function Select When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the CH Level TrimSetting the Speaker Setup When selecting the Speaker ConfigWhen selecting the Speaker Distance When selecting the LFE Level Control When selecting the Digital in Setup Setting the Function SelectWhen selecting the Input Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications RV4700 DTS-ES