DTS RV4700 DTS-ES manual Read this Before Operating Your Unit, AC Voltage Selection

Page 3

READ THIS BEFORE OPERATING YOUR UNIT

FOR U.S.A AND CANADA	120 V		FOR OTHER COUNTRIES	115 V/230 V

FOR YOUR SAFETY			FOR YOUR SAFETY

Units shipped to the U.S.A and Canada are designed for operation on 120 Volts AC only.

Observe all safety precautions for use of a polarized AC plug. However, some products may be supplied with a non polarized plug.

CAUTION: To prevent electric shock, match wide blade of plug to wide slot, insert fully.

FOR EUROPE AND AUSTRALIA

230V/240V

FOR YOUR SAFETY

Units shipped to Australia are designed for operation on 240 V AC only.

To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth.

Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician.

PAN-EUROPEAN UNIFIED VOLTAGE

All units are suitable for use on supplies 230-240 V AC.

Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel. Refer to the following paragraph for the proper setting of this switch.

AC VOLTAGE SELECTION

This unit operates on 115/230 V AC. The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction.

AC voltage selector switch

AC 230 V				AC 115 V

Move switch lever to match your line voltage with a small screwdriver or other pointed tool.

3

Image 3

Contents RV4700 DTS-ES Introduction Unpacking and InstallationAC Voltage Selection Read this Before Operating Your UnitContents Connecting Antennas Connecting Audio Components Connecting 7.1CH Direct INPUTsSystem Connections Front SUR Round Back Connecting Video ComponentsConnecting MULTI-ROOM System KIT Connecting Digital INs and OUTPRE OUT connections Switched AC Outlet AC Inlet Connecting SpeakersRoom 2 connections Fluorescent Display Front Panel ControlsLED Lamp Device Buttons Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Remote Control Operation RangeFunctions Codes Additional Information on Remote Command CodesFor Power ON/OFF Entering a Setup CodeTape Monitor function When selecting the 7.1 CH Direct as desiredOperations Before operationAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSound tracks Surround modes Surround SoundStadium TheaterMovie Hall 1/2Surround back left and right speakers Speaker placementFront left and right speakers and center speaker Surround left and right speakersEnjoying Surround Sound Selected decoding mode as followsWhen canceling the surround mode for normal stereo operation Select the desired channel Adjusting each channel levelDownmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsListening to RDS Broadcastsfm only Additional Function for RV4700 DTS-ES RDS Tuner OnlyInformation EON PTY EON Enhanced Other NetworksDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorDigital Audio Recording with MD Recorder Compressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the desired input sourceWhen selecting the CH Level Trim When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the Function SelectWhen selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance When selecting the LFE Level Control Setting the Function Select When selecting the Input SetupWhen selecting the Digital in Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Function Select for RoomProblem Possible Cause Remedy Troubleshooting GuideSpecifications RV4700 DTS-ES