DTS RV4700 DTS-ES manual Operations, Before operation, Tape Monitor function

Page 15
POWER
ON / OFF

Operations

Notes :

•Before operating this receiver with the supplied remote control, refer to “Universal Remote Controls” on page 10 for details about operation.

•Before operating this receiver, first set this unit as desired for optimum performance, doing the OSD menu setting procedures. (For details, refer to “OSD Menu Settings” on page 34.)

LISTENING TO A PROGRAM SOURCE

Before operation

• Enter the standby mode.

• The STANDBY button lights up in red. This means that the receiver is not disconnected from the AC mains and a

small amount of current is retained to support the memorized contents and operation readiness.

• To switch the power off, push the POWER switch again.

• Then power is cut off and the STANDBY button goes off.

In the standby mode, turn the power on.

1

STANDBY

ON/STANDBY

or

•Each time the STANDBY button on the front panel or the POWER button on the remote control is pressed, the receiver is turned on to enter the operating mode(the STANDBY button lights up in blue) or off to enter the standby mode (the STANDBY button lights up in red).

•In the standby mode, if one of the INPUT SELECTOR buttons is pressed, the receiver is turned on automatically and the desired input is selected.

Select the desired input source.

3

 

INPUT SELECTOR

 

AUDIO

VIDEO TAPE MON.

TUNER CD T1/MON AUX

or

VID1 VID2 VID3 VID4

• Each time the “AUDIO” button is pressed, the input source changes as follows:

TUNER CD AUX

(frequency display)

• Each time the “VIDEO” button is pressed, the input source changes as follows:

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4

•When the TAPE MONITOR button is set to on so that “TAPE MON” lights up, other inputs can not be heard from the speakers.

To listen to an input source except TAPE MONITOR, be sure to set the TAPE MONITOR button to off.

TAPE MONITOR function

You can connect either a tape deck or a graphic equalizer to the receiver’s TAPE MONITOR jacks.

Only when you listen to the component connected to these jacks, set the TAPE MONITOR button to on.

If you connect a 3-head tape deck, you can listen to the sound being recorded during recording, not the source sound.

For further details, refer to the operating instructions of the component connected.

When selecting the 7.1 CH DIRECT as desired

7.1CH DIRECT

or

DIRECT IN

Switch the speakers on.

SPEAKER

2

ON/OFF

•Then the SPEAKER indicator lights up on the display and the sound can be heard from the speakers connected to the speaker terminals.

•When using the headphones for private listening, press the SPEAKER button again to switch the speakers off.

•According to the surround back speaker setting. “7.1(,6.1 or 5.1) CH DIRECT” is displayed and the 8(/7/6) separate analog signals from 7.1 CH decoder connected to this unit pass through the tone(bass, treble) and volume circuits only and directly transfer to the speakers.(In case that the TAPE MONITOR button is set to on, the TAPE MONITOR button is automatically set to off.)

•Press the 7.1 CH DIRECT button or select the desired input source to cancel the 7.1 CH direct function.

•These 8(/7/6) separate analog signals can be heard only, not recorded.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents RV4700 DTS-ES Introduction Unpacking and InstallationAC Voltage Selection Read this Before Operating Your UnitContents Connecting Antennas Connecting Audio Components Connecting 7.1CH Direct INPUTsSystem Connections Front SUR Round Back Connecting Video ComponentsConnecting MULTI-ROOM System KIT Connecting Digital INs and OUTPRE OUT connections Switched AC Outlet AC Inlet Connecting SpeakersRoom 2 connections Fluorescent Display Front Panel ControlsLED Lamp Device Buttons Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Remote Control Operation RangeFunctions Codes Additional Information on Remote Command CodesFor Power ON/OFF Entering a Setup CodeTape Monitor function When selecting the 7.1 CH Direct as desiredOperations Before operationAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSound tracks Surround modes Surround SoundStadium TheaterMovie Hall 1/2Surround back left and right speakers Speaker placementFront left and right speakers and center speaker Surround left and right speakersEnjoying Surround Sound Selected decoding mode as followsWhen canceling the surround mode for normal stereo operation Select the desired channel Adjusting each channel levelDownmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsListening to RDS Broadcastsfm only Additional Function for RV4700 DTS-ES RDS Tuner OnlyInformation EON PTY EON Enhanced Other NetworksDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorDigital Audio Recording with MD Recorder Compressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the desired input sourceWhen selecting the CH Level Trim When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the Function SelectWhen selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance When selecting the LFE Level Control Setting the Function Select When selecting the Input SetupWhen selecting the Digital in Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Function Select for RoomProblem Possible Cause Remedy Troubleshooting GuideSpecifications RV4700 DTS-ES
Top Page Image Contents