DTS RV4700 DTS-ES manual Setting the Surround Setup, When selecting the Source Direct

Page 43

SETTING THE SURROUND SETUP

S U R R O U N D S E T U P

 

 

S O U R C E D I R E C T

:

 

Off

 

 

 

 

To select the source direct function for pure sound quality or not.

 

 

 

 

 

D E C O D I N G M O D E

:

 

AUTO

 

 

 

To select the desired decoding mode.

 

 

 

D O L B Y D I G I T A L

 

 

 

 

 

 

 

To select the desired surround mode.

 

 

 

 

 

 

 

C I N E M A E Q :

Off

 

 

 

 

 

 

To select the cinema EQ function or not.

 

 

 

 

 

 

R E T U R N : B a c k

,

 

: S e l e c t

 

 

Notes :

•Only when the digital input is selected as signal input, the decoding mode as well as the surround mode can be selected as desired.

•When the analog input is selected, only the surround mode can be selected as desired.

Press the CURSOR UP( )/DOWN( ) buttons to select the desired item.

1

• Each time these buttons are pressed, “ ” and “ ” are moved to the corresponding mode.

Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired mode.

2

• Each time these buttons are pressed, the modes change as follows according to the selected item :

When selecting the SOURCE DIRECT

•Only when playing program sources in analog stereo or digital 2 ch PCM format, the SOURCE DIRECT can be selected.

On : Select this to achieve the pure sound quality.

When this is selected, the stereo mode is automatically selected and the pure sound that bypasses the tone circuitry will be heard.

Off : Select this to cancel the source direct function.

Notes :

•When the SOURCE DIRECT is set to On, DECODING MODE, surround mode and CINEMA EQ cannot be selected.

•When you select the 7.1 CH DIRECT as input source or the digital signals from DTS, Dolby Digital or MPEG sources, etc. are input, the source direct function is automatically canceled.

When selecting the CINEMA EQ

•When 96 kHz PCM(2 channel stereo) signals are input or the source direct function is selected, the cinema EQ function can not be selected.

On : Select this to compensate for edgy or shrill movie sound tracks.

Off : Select this to cancel the cinema EQ function.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents RV4700 DTS-ES Introduction Unpacking and InstallationAC Voltage Selection Read this Before Operating Your UnitContents Connecting 7.1CH Direct INPUTs Connecting Antennas Connecting Audio ComponentsSystem Connections Front SUR Round Back Connecting Video ComponentsConnecting Digital INs and OUT Connecting MULTI-ROOM System KITPRE OUT connections AC Inlet Connecting Speakers Switched AC OutletRoom 2 connections Fluorescent Display Front Panel ControlsLED Lamp Device Buttons Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Remote Control Operation RangeFunctions Codes Additional Information on Remote Command CodesFor Power ON/OFF Entering a Setup CodeTape Monitor function When selecting the 7.1 CH Direct as desiredOperations Before operationAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSound tracks Surround modes Surround SoundStadium TheaterMovie Hall 1/2Surround back left and right speakers Speaker placementFront left and right speakers and center speaker Surround left and right speakersEnjoying Surround Sound Selected decoding mode as followsWhen canceling the surround mode for normal stereo operation Select the desired channel Adjusting each channel levelDownmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsListening to RDS Broadcastsfm only Additional Function for RV4700 DTS-ES RDS Tuner OnlyInformation EON PTY EON Enhanced Other NetworksDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorDigital Audio Recording with MD Recorder Compressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the desired input sourceWhen selecting the CH Level Trim When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the Function SelectWhen selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance When selecting the LFE Level Control When selecting the Input Setup Setting the Function SelectWhen selecting the Digital in Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Function Select for RoomProblem Possible Cause Remedy Troubleshooting GuideSpecifications RV4700 DTS-ES
Top Page Image Contents