DTS RV4700 DTS-ES manual Using the OSD, OSD Menu Settings, Current Status Display

Page 34

Using the OSD

This unit incorporates an OSD(On-screen display) function to provide information about basic operation of this unit and to simplify the setup procedures.

The OSD function uses a monitor TV connected to this unit as a display and has two kinds of display modes such as current status display and menu screen.

Notes:

•When the component video connections are made between the monitor TV and this unit, the OSD function is not available.

•Any on-screen display shown on the monitor TV will not be recorded onto VIDEO 1.

•In some countries, this unit allows you to select either NTSC or PAL color system as video format.

If it is different from your video components, video software, etc., in the standby mode, press the STANDBY button while keeping the VIDEO LABEL button pressed on the front panel, then the video format is changed to the NTSC or the PAL color system. However, it is fixed to PAL color system in other countries.

CURRENT STATUS DISPLAY

This mode shows the status corresponding to each operation.

•The on-screen display will automatically disappear in 5 seconds.

•For examples, there are 2 status displays as follows.

Note : When watching a movie earnestly, if you want to turn off the current status display function, set the OSD mode to Off.(For details, refer to “When selecting the OSD MODE” on page 42.)

When selecting the desired input source.

When selecting the TEST TONE mode.

VIDEO 1 (OPTICAL1)

FL : ------

------ : 0 dB

Input source

Signal input

Channel level or overall volume display

• When adjusting each channel level or overall volume, the volume level display will be shown.

• The test tone display will be shown until the test tone mode is canceled.

OSD Menu Settings

•The OSD menu allows you to perform the setup procedures easily. In most situations, you will only need to set this once during the installation and layout of your home theater, and it rarely needs to be changed later. The OSD menu consists of 5 main menus: speaker setup, function select, surround setup, CH level trim and room 2 feed setup. Some of these menus are divided up into various sub-menus.

• The OSD menu settings are performed easily with the CURSOR control( , , , ), ON-SCREEN DISPLAY, RETURN and ENTER buttons.

• The “3”, “7”, “8” and “9” of the NUMERIC buttons do also work as the CURSOR control( , , , )buttons do. In this case, the “3” button stands for the CURSOR UP( ) button, the “7” for the CURSOR LEFT( ), the “8” for the CURSOR DOWN( ) and the “9” for the CURSOR RIGHT( ).

Turn the menu screen on.

1

VOL. CH LEVEL

HOME THEATER MASTER

RV4700 DTS-ES

•The main menu will be shown.

•To turn the menu screen off, press this button again.

M A I N M E N U

S P E A K E R S E T U P

F U N C T I O N S E L E C T

S U R R O U N D S E T U P

C H L E V E L T R I M

R O O M 2 F E E D S E T U P

O S D : Q u i t

E N T E R : S e l e c t

•In the bottom of the display, “OSD” stands for the ON- SCREEN DISPLAY button, “RETURN” for “RETURN”, “ENTER” for “ENTER”, “ ”, “ ”, “ ” and “ ” for CURSOR UP( ), DOWN( ), LEFT( ) and RIGHT( ).

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents RV4700 DTS-ES Unpacking and Installation IntroductionRead this Before Operating Your Unit AC Voltage SelectionContents Connecting 7.1CH Direct INPUTs Connecting Antennas Connecting Audio ComponentsSystem Connections Connecting Video Components Front SUR Round BackConnecting Digital INs and OUT Connecting MULTI-ROOM System KITPRE OUT connections AC Inlet Connecting Speakers Switched AC OutletRoom 2 connections Front Panel Controls Fluorescent DisplayUniversal Remote Controls LED Lamp Device ButtonsFunction Table of the Numbered Buttons Remote Control Operation Range Loading BatteriesAdditional Information on Remote Command Codes Functions CodesEntering a Setup Code For Power ON/OFFBefore operation When selecting the 7.1 CH Direct as desiredOperations Tape Monitor functionWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSound tracks Surround Sound Surround modesHall 1/2 TheaterMovie StadiumSurround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back left and right speakersSelected decoding mode as follows Enjoying Surround SoundWhen canceling the surround mode for normal stereo operation Adjusting each channel level Select the desired channelDownmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceAdditional Function for RV4700 DTS-ES RDS Tuner Only Listening to RDS Broadcastsfm onlyEON PTY EON Enhanced Other Networks InformationRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback When selecting the desired input source Using the OSDOSD Menu Settings Current Status DisplayWhen selecting the Function Select When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the CH Level TrimSetting the Speaker Setup When selecting the Speaker ConfigWhen selecting the Speaker Distance When selecting the LFE Level Control When selecting the Input Setup Setting the Function SelectWhen selecting the Digital in Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications RV4700 DTS-ES
Top Page Image Contents