DTS RV4700 DTS-ES manual PRE OUT connections, Connecting MULTI-ROOM System KIT

Page 7

PRE OUT connections

SUB

WOOFER

L PRE R

OUT

FRONT

SUR-

ROUND

SUR-

ROUND

BACK

CENTER

Power amplifier

Front speakers

Power amplifier

Surround speakers

Power amplifier

Surround back

speakers

Power amplifier

Front center

speaker

CONNECTING MULTI-ROOM SYSTEM KIT

 

Another room

 

OUT

 

 

MULTI

 

 

Adaptor

IR receiver

Remote control unit

(Multi-room system kit)

(Multi-room system kit)

Powered subwoofer

•Use these jacks when adding additional amplifiers.

•Connect the PRE OUT jacks to the powered speakers or the power amplifiers connected to speakers respectively.

•To emphasize the deep bass sounds, connect a powered subwoofer.

•Only when enjoying 6.1 or 7.1 channel surround playback, make the surround back connections between the audio equipment.

•To control this unit from a remote location, connect this jack to the output of the multi-room adaptor.

For information on the multi-room system kit, contact the Xantech corporation at www.xantech.com.

L PRE R

 

Manufactured under license from Digital Theater System, Inc. U.S. Pat. No's.

VIDEO

 

Y

 

OUT

 

5,451,942; 5,956,674; 5,974,380; 5,978,762;

6,487,535 and other U.S. and world-wide patents

OUT

 

 

 

 

 

issued and pending. "DTS" and " DTS-ES" and "Neo:6" are trademarks of

 

S-VIDEO

 

CENTER

 

FRONT

Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc.

ROOM 2

P C

SPEAKER

 

All Rights Reserved.

IN

OUT

MODEL NO. RV4700 DTS-ES

 

 

 

 

 

FRONT

AUDIO/VIDEO RECEIVER

SUR-

Manufactured under license from

 

 

 

SPEAKERS

 

CD

MONITOR

MONITOR

P C

DESIGNED IN USA

ROUND

Dolby Laboratories. “Dolby”, “Pro Logic”,

ASSEMBLED IN KOREA

 

and the double-D symbol are

 

 

 

MONITOR

SER. NO

 

trademarks of Dolby Laboratories.

 

 

 

 

 

SUR-

 

 

 

 

 

AUX

VIDEO 1

VIDEO 1

Y

 

 

 

 

 

ROUND

OPTICAL

 

 

 

 

 

R

L

 

 

BACK

OUT

 

 

 

 

 

 

 

 

 

 

 

 

SUB

CENTER

 

 

 

MULTI

 

TAPE

 

 

P

C

 

 

 

WOOFER

 

 

 

 

MON.

 

 

SURR.

 

 

 

 

 

 

 

 

 

 

 

 

 

SPEAKERS

AC OUTLET

AM

SUB

 

 

OPTICAL

 

 

 

 

 

 

 

 

 

LOOP

WOOFER

CENTER

OPT 1

 

 

 

VIDEO 1

VIDEO 1

VIDEO 1

VIDEO 1

 

 

 

 

 

 

 

 

P C

 

 

 

 

SUR-

 

IN

 

ROOM 2

 

VIDEO 2

VIDEO 2

VIDEO 2

Y

 

R

L

 

 

ROUND

 

 

 

 

 

 

 

7.1CH

BACK

OPT 2

 

 

 

 

 

 

 

 

 

 

AC INLET

FM

DIRECT

 

 

 

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

 

 

230V~50Hz

75

 

SUR-

 

COAX1

 

TAPE

 

VIDEO 3

VIDEO 3

VIDEO 3

P

C

SURR.

370W

 

 

ROUND

 

 

MON.

 

BACK

 

 

 

 

 

REC

 

 

L

R

 

IN

 

SPEAKERS

 

 

 

 

 

 

 

IN

 

 

 

 

 

 

FRONT

 

COAX2

 

VIDEO 1

 

 

 

 

P C

 

 

 

L

R

 

 

L

R

CAUTION : TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE COVER.

 

 

 

SWITCHED

 

COAXIAL

 

NO USER-SERVICEABLE PARTS INSIDE. REFER-SERVICING TO QUALIFIED

VIDEO 2

 

 

230V~50Hz

 

 

 

IN

 

 

OUT

 

 

 

100W MAX

 

 

 

 

 

 

 

SERVICE PERSONNEL.

 

 

COMPONENT

FRONT , CENTER , SURROUND,

SURROUND BACK : 6 OHMS( ) MIN.

CONNECTING DIGITAL INs and OUT

OPTICAL

OUT

OPT 1

OPT 2

COAXIAL

IN

OPTICAL IN

COAX1

COAX2

Component(such as an MD recorder, CD recorder) with OPTICAL DIGIAL IN

Component with

OPTICAL DIGITAL OUT

Component with

OPTICAL DIGITAL OUT

Component with

COAXIAL DIGITAL OUT

Component with

COAXIAL DIGITAL OUT

• A digital input should be connected to the

components such as LD player, CD player or DVD

player, etc. capable of outputting DTS, Dolby Digital

or PCM format digital signals,etc.

• If the component with OPTICAL IN jack is connected

to the OPTICAL OUT jack of this unit, you can record

the high quality sound of CDs etc. without

degradation.

• For details, refer to the operating instructions of the

component connected.

• When making the COAXIAL DIGITAL connection, be

sure to use a 75 Ω COAXIAL cord, not a conventional

AUDIO cord.

•The COAXIAL or the OPTICAL DIGITAL OUTs of the components that are connected to CD, TAPE MONITOR and VIDEO 1 - VIDEO 4 of this unit can be connected to these DIGITAL INs.

•After making digital connections, be sure to match the DIGITAL INs to the corresponding input source respectively. (For details, refer to "When selecting the DIGITAL IN SETUP" on page 39.)

• All of the commercially available optical fiber cords

cannot be used for the equipment. If there is an

optical fiber cord which cannot be connected to your

equipment, consult your dealer or nearest service

organization.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents RV4700 DTS-ES Introduction Unpacking and InstallationAC Voltage Selection Read this Before Operating Your UnitContents Connecting 7.1CH Direct INPUTs Connecting Antennas Connecting Audio ComponentsSystem Connections Front SUR Round Back Connecting Video ComponentsConnecting Digital INs and OUT Connecting MULTI-ROOM System KITPRE OUT connections AC Inlet Connecting Speakers Switched AC OutletRoom 2 connections Fluorescent Display Front Panel ControlsLED Lamp Device Buttons Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Remote Control Operation RangeFunctions Codes Additional Information on Remote Command CodesFor Power ON/OFF Entering a Setup CodeTape Monitor function When selecting the 7.1 CH Direct as desiredOperations Before operationAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSound tracks Surround modes Surround SoundStadium TheaterMovie Hall 1/2Surround back left and right speakers Speaker placementFront left and right speakers and center speaker Surround left and right speakersEnjoying Surround Sound Selected decoding mode as followsWhen canceling the surround mode for normal stereo operation Select the desired channel Adjusting each channel levelDownmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsListening to RDS Broadcastsfm only Additional Function for RV4700 DTS-ES RDS Tuner OnlyInformation EON PTY EON Enhanced Other NetworksDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorDigital Audio Recording with MD Recorder Compressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the desired input sourceWhen selecting the CH Level Trim When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the Function SelectWhen selecting the Speaker Config Setting the Speaker SetupWhen selecting the Speaker Distance When selecting the LFE Level Control When selecting the Input Setup Setting the Function SelectWhen selecting the Digital in Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Function Select for RoomProblem Possible Cause Remedy Troubleshooting GuideSpecifications RV4700 DTS-ES
Top Page Image Contents