DTS RV4700 DTS-ES manual Setting the ROOM2 Feed Setup, When selecting the Volume Mode

Page 46

SETTING THE ROOM2 FEED SETUP

R O O M 2 F E E D S E T U P

V O L U M E M O D E

 

 

 

 

To select the desired volume mode.

 

 

 

 

F U N C T I O N S E L E C T

 

 

 

To select the desired ROOM 2 source.

 

 

 

R E T U R N : B a c k

E N T E R : S e l e c t

 

 

 

 

 

 

The ROOM 2 function allows enjoying one source in the main room and playing another in a different room at the same time.

The analog signals from the 7.1 CH DIRECT inputs and TAPE MONITOR INs as well as the digital signals from the coaxial or optical digital input cannot be output from the ROOM2 OUTs, meaning no playback in a different room.

When selecting the VOLUME MODE

Press the CURSOR UP( )/DOWN( ) buttons to select the VOLUME MODE, then press the ENTER

1 button.

V O L U M E M O D E

VOL. CH LEVEL

ENTER

V O L U M E M O D E : Variable

HOME THEATER MASTER

RV4700 DTS-ES

R E T U R N : B a c k

, : S e l e c t

Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired volume mode for the ROOM 2

2 source.

VOL. CH LEVEL

HOME THEATER MASTER

RV4700 DTS-ES

Each time these buttons are pressed, the volume mode changes as follows:

Variable : Select this when an power amplifier is connected to the ROOM 2(audio) OUTs for ROOM 2 source playback. You can adjust the ROOM 2 volume level with the MASTER VOLUME CONTROL knob of this receiver or the VOLUME UP/DOWN buttons on the remote control.

Fixed : Select this when an integrated amplifier, etc. is connected to the ROOM 2(audio) OUTs. You can adjust the ROOM 2 volume level on the connected integrated amplifier, etc.

Notes :

When selecting the Fixed mode, first adjust the volume level as desired in the Variable mode and select the Fixed mode. Then the volume level will be fixed to the adjusted level.

In case that an integrated amplifier, etc. is connected to the ROOM 2(audio) OUTs and the volume mode is set to Variable, if the ROOM 2 volume level is adjusted to high level on both this receiver and the connected amplifier, the ROOM 2 speaker and the connected amplifier may be damaged.

Therefore, be sure to set the volume mode to Fixed for safe operation.

46

Image 46
Contents RV4700 DTS-ES Unpacking and Installation IntroductionRead this Before Operating Your Unit AC Voltage SelectionContents Connecting 7.1CH Direct INPUTs Connecting Antennas Connecting Audio ComponentsSystem Connections Connecting Video Components Front SUR Round BackConnecting Digital INs and OUT Connecting MULTI-ROOM System KITPRE OUT connections AC Inlet Connecting Speakers Switched AC OutletRoom 2 connections Front Panel Controls Fluorescent DisplayUniversal Remote Controls LED Lamp Device ButtonsFunction Table of the Numbered Buttons Remote Control Operation Range Loading BatteriesAdditional Information on Remote Command Codes Functions CodesEntering a Setup Code For Power ON/OFFBefore operation When selecting the 7.1 CH Direct as desiredOperations Tape Monitor functionWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSound tracks Surround Sound Surround modesHall 1/2 TheaterMovie StadiumSurround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back left and right speakersSelected decoding mode as follows Enjoying Surround SoundWhen canceling the surround mode for normal stereo operation Adjusting each channel level Select the desired channelDownmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceAdditional Function for RV4700 DTS-ES RDS Tuner Only Listening to RDS Broadcastsfm onlyEON PTY EON Enhanced Other Networks InformationRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback When selecting the desired input source Using the OSDOSD Menu Settings Current Status DisplayWhen selecting the Function Select When selecting the Speaker SetupWhen selecting the Surround Setup When selecting the CH Level TrimSetting the Speaker Setup When selecting the Speaker ConfigWhen selecting the Speaker Distance When selecting the LFE Level Control When selecting the Input Setup Setting the Function SelectWhen selecting the Digital in Setup When selecting the Video Select When selecting the Tone Control When selecting the OSD Mode When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications RV4700 DTS-ES