FUNAI CR130TT8 owner manual Troubleshooting Guide

Page 22

TROUBLESHOOTING

5Troubleshooting Guide

If the unit does not perform properly when operated as instructed in this operation manual, check the following chart once before calling for service.

Symptom

Remedy

No power	• Be sure the power cord is plugged in.
	• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to
	reset itself.
No picture or sound	• Check if the power is on.
	• Check the outlet connection.
	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
	• Turn off the power and wait for about 1 minute, then turn it on again.
No color	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
	• Adjust the “COLOR” in the setup screen.
Sound OK, picture poor	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• Adjust “CONTRAST” and “BRIGHT” in the setup screen.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture distorted	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
Weak picture	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Adjust “CONTRAST” and “BRIGHT” in the setup screen.
	• View other TV channels. The problem might be limited to the broadcasting station.
Lines or streaks in picture	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture blurred	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
Ghosts in picture	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Bars on screen	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
Picture rolls vertically	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Different color marks on	• Move the unit away from nearby electric appliances. Turn off the power and wait
screen	30 minutes before turning it back on.
	• View other TV channels. The problem might be limited to the broadcasting station.
Poor reception on some	• Check the antenna or cable connection to the main unit.
channels	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture OK, sound poor	• View other TV channels. The problem might be limited to the broadcasting station.

No reception of digital signals	• Make sure auto channel scan has been completed (Refer to “Auto Channel Scan” on
	page 11).
	Auto channel scan must be completed when you set up the unit for the first time
	or move it to a location where previously unavailable channels are broadcast.
	• The selected channel may not be broadcasting.
	• When auto channel scan is interrupted and not completed, some channels will not
	be received. Make sure to complete (Refer to “Auto Channel Scan” on page 11).

22

EN

Image 22

Contents CR130TT8 Introduction Important note is located on the rear of the cabinetPrecautions RADIO-TV InterferenceLocation Supplied AccessoriesSymbols Used in this Manual To Avoid the Hazards of Electrical Shock and FireContents FeaturesDTV/TV/CATV Installing the Batteries Remote Control FunctionBattery Precautions Rear Panel AC power cordControl Panel ANT. in jack p8Antenna Cable Connection ConnectionBasic Connection Connection to Cable Box or Satellite BoxRCA video cable RCA audio cable External Device ConnectionVideo Connection Digital Audio Output ConnectionMain Menu Initial SettingInitial Setup Before you beginPress Menu to display the main menu Auto Channel ScanLanguage Selection English Español FrançaisWatching TV Volume AdjustmentChannel Selection Accessing External Devices Switching Digital / Analog ModeScreen Information To Cancel the Sleep Timer TV Screen Display ModeSleep Timer LetterboxUse VOL X/Y to select ADD or Delete Optional SettingChannel Add/Delete To add or delete another channels, repeat steps 4 toPicture Adjustment Closed CaptionDtvcc Then press VOLDtvcc Style Chip DpageTo Set the Sub Ratings Enter password again in Confirm Password space Mpaa RatingTroubleshooting Troubleshooting GuideWith an AM radio MaintenanceWith a digital camera Including built-in cell phone cameras Information Memo Limited Warranty 13 Télévision Numérique / Analogique Importantes Consignes de Sécurité Précautions à Prendre Brouillage RADIO-TVEmplacement Accessoires FournisSymboles Utilisés dans ce Manuel Pour Éviter LES Risques DE Choc Électrique ET D’INCENDIECaractéristiques ContenuInsérer les Piles Fonction de TélécommandePrécautions Concernant les Piles Panneau de Commande Panneau ArrièreRemarque ConnexionConnexion de Base Connexion du Câble d’AntenneCâble audio RCA Connexion d’un Appareil ExterneConnexion Vidéo Connexion par la Sortie Audio NumériqueMenu Principal Configuration InitialeInstallation Initiale PréliminairesMenu sur écran Ex. mode TV numérique5Sélection de la Langue EnglishSélection de Chaîne Réglage du VolumeRegarder LA Télévision Pour utiliser les touches NumériquesInformations DE Diffusion Informations sur ÉcranAffichées Informations de DiffusionAppuyezsommeil. sur Sleep pour régler la minuterie de Minuterie de SommeilPour annuler la minuterie de sommeil Configuration Optionnelle Ajout/Suppression de ChaîneTeinte 5Réglage de l’ImageCouleur NettetéPuis appuyez sur VOL Ex. mode TV numérique Utilisez CH K / L pour sélectionner CONFIG. DTVSous-titres DTV Style Dtvcc Circuit Pour Spécifier les Cotes Secondaires Saisissez de nouveau le mode de passe dans l’espace DE PASSE, puis appuyez sur VOL Ex. mode TV numériqueTélécommande pour saisir le nouveau mot de passe à Chiffres Appuyez sur les touchesDépannage Guide de DépannageAvec une radio AM Réglez la radio AM sur une fréquence non EntretienAvec un appareil photo numérique Spécifications Générales GlossaireDésignation des Chaînes de Câblodiffusion Spécifications ÉlectriquesMemo Garantie Limitée Manual del Usuario Importante para su Seguridad IntroducciónPrecauciones Interferencia DE RADIO-TELEVISIÓNManual del usuario Accesorios SuministradosSímbolos Utilizados en este Manual Pilas AA xCaracterísticas ContenidoInstalación de las Pilas Función de Mando a DistanciaPrecauciones Sobre las Pilas Panel de Control Panel TraseroNota ConexiónConexión Básica Conexión de Cable de AntenaCable RCA de vídeo Conexión de Dispositivo ExternoConexión de Cable de Vídeo Conexión de Salida de Audio DigitalMenú Principal Configuración InicialAjuste Inicial Antes de empezarPresintonía deseado, y presione VOL Presione Menu para visualizar el menú principalUtilice CH K/L para seleccionar su tipo de Presione Menu para salirSelección de Canal Ajuste de VolumenPara VER LA Televisión Para utilizar los botones numéricosInformación de Pantalla Para Cambiar Entre el Modo Digital y el Modo AnalógicoAcceso a Dispositivos Externos Información de EmisiónPresione Menu para mostrar el menú principal Modo de Visualización de Pantalla del TelevisorTemporizador de Apagado Ancho BuzónAgregar/Borrar Canales Ajuste OpcionalEj. modo TV digital OFF Ajuste de ImagenSubtítulos Cerrados Utilice VOL X / Y para ajustar la calidadSelecciónelo si no desea Utilice CHUtilice VOL X/Y repetidamente para cambiar el ajuste DTVCC. Éste es el ajuste PredeterminadoEstilo Dtvcc Cuando no haya configurado su contraseña, introduzca DpáginaLas subcategorías, siga los pasos indicados Para Ajustar las SubcategoríasEj. TV-PG Vuelva a introducir la contraseña en el espacio Exclusivamente para público adultoSolución DE Problemas Guía de Solución de ProblemasCon una radio AM MantenimientoCon una cámara digital Información EMO Garantía Limitada