Eiki LC-XC1 Turning on the Projector, Turning OFF the Projector, Appliance cannot be turned on

Page 20

LC-XC1

TURNING ON THE PROJECTOR

1. Complete the peripheral connections (with Computer, VCR, etc.) before turning on the projector. (Refer to

2

3

“CONNECTING TO THE PROJECTOR” on Pages 11-~14 for connecting that equipment.)

Connect the projector’s AC Power Cord into a wall outlet and

turn the MAIN ON I OFF SWITCH to ON. The LAMP indicator

lights RED, and the READY indicator lights GREEN.

Press the POWER ON-OFF button on the Remote Control

Unit or on the Top Control to ON. The LAMP indicator dims, and the Cooling Fans start to operate. The Preparation Display

appears on the screen and the count-down starts. The signal from the source appears after 30 seconds.

TURNING OFF THE PROJECTOR

1. Press the power ON-OFF button on the Remote Control Unit or on the Top Control, and the message “Power off?” appears on the screen.

2 Press the power ON-OFF button again to turn off the projector. The LAMP indicator lights bright and the READY indicator turns off. After the projector is turned off, the Cooling Fans operate (for about 90 seconds). During this “Cooling Down” period, this

appliance cannot be turned on.

3 When the projector has cooled down, the READY indicator turns to green again and you can turn the projector on. After cooling down completely, turn the MAIN ON I OFF SWITCH to OFF and disconnect the AC power cord.

TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU

TURN THE PROJECTOR ON, WAIT AT LEAST 5

MINUTES BEFORE TURNING IT OFF.

When the Power Management function is ON, the Projector detects the signal interruption and turns the Projection Lamp off automatically. Refer to “Power Management” on page 33.

When WARNING TEMP. indicator flashes red, the projector is automatically turned oft. Wait at least 5 minutes before turning the projector on again.

When WARNING TEMP indicator continues to flash, follow procedures below:

1.Turn the MAIN ON I OFF SWITCH to OFF and disconnect the AC power cord from the AC outlet.

2.Check the air filters for dust accumulation.

3.Clean the Air Filter. (See “AIR FILTER CARE AND CLEANING” section on page 39.)

4.Turn the Projector on again.

If WARNING TEMP indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center.

NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling Fan is working, WARNING TEMP. INDICATOR flashes red.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model LC-XC1 To the Owner Safety Instructions Compliances Table of Contents Progressive scan signals and provide fine picture quality Projector and computer with this Remote Control Unit onlyIBM-compatible and Macintosh computers up to Color SystemsLC-XC1 Projector side AC Outlet side Positioning the Projector Room LightAdjustable Feet Latches on both sides of the projectorInput Terminals Reset function excessively When using the Wired / WirelessThis projector uses a micro processor to control Refer toLC-XC1 LC-XC1 Indicators Laser Pointer Function Replace Compartment lidFlow of ON-SCREEN Menu Menu BAR Turn the Main on I OFF Switch to ON. The Lamp indicator Turning on the ProjectorTurning OFF the Projector Appliance cannot be turned onZoom Adjustment Focus AdjustmentLens Shift Adjustment Press the Zoom !/∀buttons on the Top Control or onKeystone Adjustment Timer functionPicture Freeze Function ∀button or the Point UP/DOWN buttons. PressDirect Operation Menu OperationTo set the Computer system manually, select the mode on No signalAutomatic MULTI-SCAN System System Menu will appearCompatible Computer Specifications Point UP/DOWN button and the Select button. To Reset Mode free Stored Quit Recalls the data previously adjusted ResetStores the adjusted data in the memory Closes Image MenuNormal Function Closes Setting data in the memoryLEFT/RIGHT buttons, and then press the Select button ∀, SELECT, Right CLICK, or Point button. To adjust Displayed. Correct the Keystone distortion by pressingMenu P24 This projector cannot display anyVideo I S-Video / Y, PbICb, Pr/Cr Direct OperationMenu Operation Video Signal from Video Jack or S-VIDEO Jack Video Signal from Y, Pb/Cb, Pr/Cr JacksCustom ColorNoise reduction ProgressiveRegular WideBlue back Power off? messageDisplay Remote control Set the Remote control in Setting Menu to ModeTo return to the normal code Mode 1, operate both projector Returns to the normal code ModeInstallation Operating Wireless MouseConnection Not work properlyParticles, it will reduce the Cooling Fans’ Temperature Warning IndicatorAIR Filter Care and Cleaning Lamp Replacement Monitor Timer CoverCleaning ThE Projection Lens Picture is Top/Bottom Reversed Some displays are notSeen during No imageCabinet Dimensions W x H x D Net WeightPanel Resolution Signal Scanning FrequencyMAC Adapter Terminal HDB1 5-PINTerminal DVI 24-pin Terminal Mini DIN 8-PINEiki Deutschland Gmbh
Top Page Image Contents