Eiki LC-XC1 owner manual To the Owner

Page 2

LC-XC1

TO THE OWNER

Before operating this projector, read this manual thoroughly and operate the projector properly.

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.

Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.

If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.

SAFETY PRECAUTIONS

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This projector produces intense light from the projection lens. Do not stare directly into the lens as possible.

Eye damage could result. Be especially careful that children do not stare directly into the beam.

This projector should be set in the way indicated. If not, it may result in a fire hazard.

Take appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. Minimum distance should be taken. If the projector is to be built into a compartment or similarly

enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.

Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.

The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the Laser Light Window while pressing the LASER button (for 1. minute). Do not look into the Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.

If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER’S MANUAL FOR LATER USE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS

VOLTAGE CONSTITUTING A RISK OF ELECTRIC

SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT

OPERATING AND MAINTENANCE INSTRUCTIONS IN THE

OWNER’S MANUAL WITH THIS UNIT.

2

Image 2
Contents Model LC-XC1 To the Owner Safety Instructions Compliances Table of Contents IBM-compatible and Macintosh computers up to Progressive scan signals and provide fine picture qualityProjector and computer with this Remote Control Unit only Color SystemsLC-XC1 Projector side AC Outlet side Positioning the Projector Room LightAdjustable Feet Latches on both sides of the projectorInput Terminals This projector uses a micro processor to control Reset function excessivelyWhen using the Wired / Wireless Refer toLC-XC1 LC-XC1 Indicators Laser Pointer Function Replace Compartment lidFlow of ON-SCREEN Menu Menu BAR Turning OFF the Projector Turn the Main on I OFF Switch to ON. The Lamp indicatorTurning on the Projector Appliance cannot be turned onLens Shift Adjustment Zoom AdjustmentFocus Adjustment Press the Zoom !/∀buttons on the Top Control or onPicture Freeze Function Keystone AdjustmentTimer function ∀button or the Point UP/DOWN buttons. PressDirect Operation Menu OperationAutomatic MULTI-SCAN System To set the Computer system manually, select the mode onNo signal System Menu will appearCompatible Computer Specifications Point UP/DOWN button and the Select button. To Reset Mode free Stored Quit Stores the adjusted data in the memory Recalls the data previously adjustedReset Closes Image MenuNormal Function Closes Setting data in the memoryLEFT/RIGHT buttons, and then press the Select button Menu P24 ∀, SELECT, Right CLICK, or Point button. To adjustDisplayed. Correct the Keystone distortion by pressing This projector cannot display anyVideo I S-Video / Y, PbICb, Pr/Cr Direct OperationMenu Operation Video Signal from Video Jack or S-VIDEO Jack Video Signal from Y, Pb/Cb, Pr/Cr JacksNoise reduction CustomColor ProgressiveRegular WideBlue back Power off? messageDisplay To return to the normal code Mode 1, operate both projector Remote controlSet the Remote control in Setting Menu to Mode Returns to the normal code ModeConnection InstallationOperating Wireless Mouse Not work properlyParticles, it will reduce the Cooling Fans’ Temperature Warning IndicatorAIR Filter Care and Cleaning Lamp Replacement Monitor Timer CoverCleaning ThE Projection Lens Seen during Picture isTop/Bottom Reversed Some displays are not No imageCabinet Panel Resolution Dimensions W x H x DNet Weight Signal Scanning FrequencyTerminal DVI 24-pin MAC AdapterTerminal HDB1 5-PIN Terminal Mini DIN 8-PINEiki Deutschland Gmbh