Eiki LC-XC1 owner manual Adjustable Feet, Latches on both sides of the projector

Page 10

LC-XC1

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by rotating the ADJUSTABLE FEET. Projection angle can be adjusted to 9.0 degrees.

1

2

Lift the front of the projector and pull the FEET LOCK

LATCHES on both sides of the projector.

Release the FEET LOCK LATCHES to lock the

ADJUSTABLE FEET and rotate the ADJUSTABLE FEET to fine tune the position and the tilt.

3 To shorten the ADJUSTABLE FEET, lift the front of the projector and pull and undo the FEET LOCK LATCHES.

The position and the keystone distortion of the image can be adjusted using the Menu Operation. (Refer to P 22,

31 and 35.)

MOVING THE PROJECTOR

Use the Carry Handle when moving the Projector. When moving the projector, replace the lens cover and retract the feet to prevent damage to the lens and cabinet.

When this projector is not in use for an extended period, put it into the case (dust cover) supplied with this projector.

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

•Do not drop or bump the projector, otherwise damages or malfunctions may result.

•When carrying the projector, use a suitable carrying case.

•Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause damage to the projector. To transport the projector through a courier or transport service, consult your dealer for best way.

10

Image 10

Contents Model LC-XC1 To the Owner Safety Instructions Compliances Table of Contents IBM-compatible and Macintosh computers up to Progressive scan signals and provide fine picture qualityProjector and computer with this Remote Control Unit only Color SystemsLC-XC1 Projector side AC Outlet side Positioning the Projector Room LightAdjustable Feet Latches on both sides of the projectorInput Terminals This projector uses a micro processor to control Reset function excessivelyWhen using the Wired / Wireless Refer toLC-XC1 LC-XC1 Indicators Laser Pointer Function Replace Compartment lidFlow of ON-SCREEN Menu Menu BAR Turning OFF the Projector Turn the Main on I OFF Switch to ON. The Lamp indicatorTurning on the Projector Appliance cannot be turned onLens Shift Adjustment Zoom AdjustmentFocus Adjustment Press the Zoom !/∀buttons on the Top Control or onPicture Freeze Function Keystone AdjustmentTimer function ∀button or the Point UP/DOWN buttons. PressDirect Operation Menu OperationAutomatic MULTI-SCAN System To set the Computer system manually, select the mode onNo signal System Menu will appearCompatible Computer Specifications Point UP/DOWN button and the Select button. To Reset Mode free Stored Quit Stores the adjusted data in the memory Recalls the data previously adjustedReset Closes Image MenuNormal Function LEFT/RIGHT buttons, and then press the Select button Setting data in the memoryCloses Menu P24 ∀, SELECT, Right CLICK, or Point button. To adjustDisplayed. Correct the Keystone distortion by pressing This projector cannot display anyMenu Operation Direct OperationVideo I S-Video / Y, PbICb, Pr/Cr Video Signal from Video Jack or S-VIDEO Jack Video Signal from Y, Pb/Cb, Pr/Cr JacksNoise reduction CustomColor ProgressiveRegular WideDisplay Power off? messageBlue back To return to the normal code Mode 1, operate both projector Remote controlSet the Remote control in Setting Menu to Mode Returns to the normal code ModeConnection InstallationOperating Wireless Mouse Not work properlyAIR Filter Care and Cleaning Temperature Warning IndicatorParticles, it will reduce the Cooling Fans’ Lamp Replacement Monitor Timer CoverCleaning ThE Projection Lens Seen during Picture isTop/Bottom Reversed Some displays are not No imageCabinet Panel Resolution Dimensions W x H x DNet Weight Signal Scanning FrequencyTerminal DVI 24-pin MAC AdapterTerminal HDB1 5-PIN Terminal Mini DIN 8-PINEiki Deutschland Gmbh