Eiki LC-XC1 owner manual Temperature Warning Indicator, AIR Filter Care and Cleaning

Page 39

LC-XC1

TEMPERATURE WARNING INDICATOR

WARNING TEMP. Indicator flashes red when the internal temperature of the projector exceeds the normal

temperature. The Indicator stops flashing when the temperature of the projector returns to normal.

When WARNING TEMP. Indicator continues to flash, check the items listed below.

1 The Ventilation slots of the projector may be blocked. In such an event, reposition the appliance so that the ventilation slots are not obstructed.

2

3

Air filters may be clogged with dust particles. Clean the air filters by following the section AIR FILTER CARE AND CLEANING below.

If WARNING TEMP. Indicator remains on after performing the above checks, the Cooling Fans or the Internal Circuits may be malfunctioning. Contact service a personnel from an authorized dealer or service station.

AIR FILTER CARE AND CLEANING

The Removable Air Filter prevents dust from accumulating on the surface of the Projection Lens and the

Projection Mirror. Should the Air Filter become clogged with dust

particles, it will reduce the Cooling Fans’

effectiveness and may result in internal heat build up and adversely affect the life of the projector.

Clean the Air Filter following the steps below:

1

2

Turn the power off, and disconnect the AC power cord from the AC outlet.

Turn the projector upside down and remove the Air Filter Cover

by pressing four latches sideways and pulling up. Remove three Air Filters by pulling up the latches.

3

4

Clean the Air Filters with brush or wash out the dust and particles. Be sure to dry them out.

Replace the Air Filters and Air Filter Cover properly. Make sure that they are fully set.

CAUTION

Do not operate the projector with the Air Filter removed. Dust may accumulate on the LCD Panel and the Mirror degrading picture quality. Do not put small parts into the Air Intake Vents. It may result in malfunction of the proiector.

RECOMMENDATION

We recommend avoiding dusty/smoky environments when operating the projector. Usage in these environments may cause poor image quality.

When using under dusty or smoky conditions, dust may accumulate on the liquid crystal panel, lens, or optical elements inside it. This condition may degrade the quality of the projected image. When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Model LC-XC1 To the Owner Safety Instructions Compliances Table of Contents Color Systems Progressive scan signals and provide fine picture qualityProjector and computer with this Remote Control Unit only IBM-compatible and Macintosh computers up toLC-XC1 Projector side AC Outlet side Room Light Positioning the ProjectorLatches on both sides of the projector Adjustable FeetInput Terminals Refer to Reset function excessivelyWhen using the Wired / Wireless This projector uses a micro processor to controlLC-XC1 LC-XC1 Indicators Laser Pointer Function Compartment lid ReplaceFlow of ON-SCREEN Menu Menu BAR Appliance cannot be turned on Turn the Main on I OFF Switch to ON. The Lamp indicatorTurning on the Projector Turning OFF the ProjectorPress the Zoom !/∀buttons on the Top Control or on Zoom AdjustmentFocus Adjustment Lens Shift Adjustment∀button or the Point UP/DOWN buttons. Press Keystone AdjustmentTimer function Picture Freeze FunctionMenu Operation Direct OperationSystem Menu will appear To set the Computer system manually, select the mode onNo signal Automatic MULTI-SCAN SystemCompatible Computer Specifications Point UP/DOWN button and the Select button. To Reset Mode free Stored Quit Closes Image Menu Recalls the data previously adjustedReset Stores the adjusted data in the memoryNormal Function Setting data in the memory LEFT/RIGHT buttons, and then press the Select buttonCloses This projector cannot display any ∀, SELECT, Right CLICK, or Point button. To adjustDisplayed. Correct the Keystone distortion by pressing Menu P24Direct Operation Menu OperationVideo I S-Video / Y, PbICb, Pr/Cr Video Signal from Y, Pb/Cb, Pr/Cr Jacks Video Signal from Video Jack or S-VIDEO JackProgressive CustomColor Noise reductionWide RegularPower off? message DisplayBlue back Returns to the normal code Mode Remote controlSet the Remote control in Setting Menu to Mode To return to the normal code Mode 1, operate both projectorNot work properly InstallationOperating Wireless Mouse ConnectionTemperature Warning Indicator AIR Filter Care and CleaningParticles, it will reduce the Cooling Fans’ Cover Lamp Replacement Monitor TimerCleaning ThE Projection Lens No image Picture isTop/Bottom Reversed Some displays are not Seen duringCabinet Signal Scanning Frequency Dimensions W x H x DNet Weight Panel ResolutionTerminal Mini DIN 8-PIN MAC AdapterTerminal HDB1 5-PIN Terminal DVI 24-pinEiki Deutschland Gmbh
Top Page Image Contents