Eiki LC-XC1 owner manual Lamp Replacement Monitor Timer, Cover

Page 40

LC-XC1

LAMP REPLACEMENT

When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow. When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is required.

CAUTION

• For continued safety, replace with a lamp assembly of the same type.

•AIlow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.

•Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury. Follow these steps to replace the lamp assembly.

1

2

3

4

Turn off the projector and disconnect the AC plug. Allow the projector to cool for at least 45 minutes.

Remove the screw with a screwdriver and remove the Lamp

Cover.

Remove the two screws with a screwdriver and pull out the

Lamp Assembly by grasping the handle.

Replace the Lamp Assembly with a new one and tighten the

two screws. Make sure that the Lamp Assembly is set properly. Replace the Lamp Cover and tighten the screw.

5 Connect the AC Power Cord to the projector and turn the projector on.

6 Reset the Lamp Replacement Monitor Timer (refer to the section

“Lamp Replacement Monitor Timer” below).

NOTE: Do not reset the LAMP REPLACEMENT MONITOR

TIMER when the lamp is not replaced.

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering the Lamp, give the following information to the dealer.

• Model No. of your projector : LC-XC1

• Replacement Lamp Type No.: POA-LMP28

(Service Parts No. 610 285 4824)

LAMP REPLACEMENT MONITOR TIMER

Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.

1 Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SETTING and press the SELECT button (refer to the page 36, 37). Another dialog box SETTING MENU will appear.

2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to “Lamp age,” and then press the SELECT button. The message “Lamp replace monitor Reset?” is displayed.

3 Select to reset the Timer.

Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Model LC-XC1 To the Owner Safety Instructions Compliances Table of Contents Progressive scan signals and provide fine picture quality Projector and computer with this Remote Control Unit onlyIBM-compatible and Macintosh computers up to Color SystemsLC-XC1 Projector side AC Outlet side Positioning the Projector Room LightAdjustable Feet Latches on both sides of the projectorInput Terminals Reset function excessively When using the Wired / WirelessThis projector uses a micro processor to control Refer toLC-XC1 LC-XC1 Indicators Laser Pointer Function Replace Compartment lidFlow of ON-SCREEN Menu Menu BAR Turn the Main on I OFF Switch to ON. The Lamp indicator Turning on the ProjectorTurning OFF the Projector Appliance cannot be turned onZoom Adjustment Focus AdjustmentLens Shift Adjustment Press the Zoom !/∀buttons on the Top Control or onKeystone Adjustment Timer functionPicture Freeze Function ∀button or the Point UP/DOWN buttons. PressDirect Operation Menu OperationTo set the Computer system manually, select the mode on No signalAutomatic MULTI-SCAN System System Menu will appearCompatible Computer Specifications Point UP/DOWN button and the Select button. To Reset Mode free Stored Quit Recalls the data previously adjusted ResetStores the adjusted data in the memory Closes Image MenuNormal Function LEFT/RIGHT buttons, and then press the Select button Setting data in the memoryCloses ∀, SELECT, Right CLICK, or Point button. To adjust Displayed. Correct the Keystone distortion by pressingMenu P24 This projector cannot display anyMenu Operation Direct OperationVideo I S-Video / Y, PbICb, Pr/Cr Video Signal from Video Jack or S-VIDEO Jack Video Signal from Y, Pb/Cb, Pr/Cr JacksCustom ColorNoise reduction ProgressiveRegular WideDisplay Power off? messageBlue back Remote control Set the Remote control in Setting Menu to ModeTo return to the normal code Mode 1, operate both projector Returns to the normal code ModeInstallation Operating Wireless MouseConnection Not work properlyAIR Filter Care and Cleaning Temperature Warning IndicatorParticles, it will reduce the Cooling Fans’ Lamp Replacement Monitor Timer CoverCleaning ThE Projection Lens Picture is Top/Bottom Reversed Some displays are notSeen during No imageCabinet Dimensions W x H x D Net WeightPanel Resolution Signal Scanning FrequencyMAC Adapter Terminal HDB1 5-PINTerminal DVI 24-pin Terminal Mini DIN 8-PINEiki Deutschland Gmbh
Top Page Image Contents