Schneider Electric 312 manual Configuration, Coding the drive address, Address Switches 5-4-3-2-1

Configuration

Coding the drive address

An Altivar 312 is identified on the bus by its address, coded between 0 and 126.

The address corresponds to the binary number given by position 0 (up/OFF) or 1 (down/ON) of the 7 switches on the left of the card.

The least significant bits are on the right.

The table below indicates the positions of the switches for all configurable addresses:

Address	Switches	Address	Switches	Address	Switches	Address	Switches	Address	Switches
	7-6-5-4-3-2-1		7-6-5-4-3-2-1		7-6-5-4-3-2-1		7-6-5-4-3-2-1		7-6-5-4-3-2-1
0	000 0000	26	001 1010	52	011 0100	78	100 1110	104	110 1000
1	000 0001	27	001 1011	53	011 0101	79	100 1111	105	110 1001
2	000 0010	28	001 1100	54	011 0110	80	101 0000	106	110 1010
3	000 0011	29	001 1101	55	011 0111	81	101 0001	107	110 1011
4	000 0100	30	001 1110	56	011 1000	82	101 0010	108	110 1100
5	000 0101	31	001 1111	57	011 1001	83	101 0011	109	110 1101
6	000 0110	32	010 0000	58	011 1010	84	101 0100	110	110 1110
7	000 0111	33	010 0001	59	011 1011	85	101 0101	111	110 1111
8	000 1000	34	010 0010	60	011 1100	86	101 0110	112	111 0000
9	000 1001	35	010 0011	61	011 1101	87	101 0111	113	111 0001
10	000 1010	36	010 0100	62	011 1110	88	101 1000	114	111 0010
11	000 1011	37	010 0101	63	011 1111	89	101 1001	115	111 0011
12	000 1100	38	010 0110	64	100 0000	90	101 1010	116	111 0100
13	000 1101	39	010 0111	65	100 0001	91	101 1011	117	111 0101
14	000 1110	40	010 1000	66	100 0010	92	101 1100	118	111 0110
15	000 1111	41	010 1001	67	100 0011	93	101 1101	119	111 0111
16	001 0000	42	010 1010	68	100 0100	94	101 1110	120	111 1000
17	001 0001	43	010 1011	69	100 0101	95	101 1111	121	111 1001
18	001 0010	44	010 1100	70	100 0110	96	110 0000	122	111 1010
19	001 0011	45	010 1101	71	100 0111	97	110 0001	123	111 1011
20	001 0100	46	010 1110	72	100 1000	98	110 0010	124	111 1100
21	001 0101	47	010 1111	73	100 1001	99	110 0011	125	111 1101
22	001 0110	48	011 0000	74	100 1010	100	110 0100	126	111 1110
23	001 0111	49	011 0001	75	100 1011	101	110 0101		111 1111
24	001 1000	50	011 0010	76	100 1100	102	110 0110
25	001 1001	51	011 0011	77	100 1101	103	110 0111

•Addresses 0 and 1 are usually reserved for the PROFIBUS DP masters and must not be used to configure the PROFIBUS DP address on an Altivar 312.

•It is not advised to use address 126, which is incompatible with SSA service (Set Slave Address) and with some network configuration softwares (Sycon, ...).

Example for DP address = 2:

Dip switch 8 is not connected.

14 S1A10386 10/2009