Schneider Electric LXM32M manual Status LEDs, Color Status Meaning

Page 70

7 Diagnostics and troubleshooting	LXM32M

7.2Status LEDs

The status of the module is indicated by four LEDs.

1 2

A

B

3 4

Figure 12: Overview of the LEDs at the module

(1)Network activity interface A

(2)Module status

(3)Network activity interface B

(4)Network status

NOTE: The meaning of the flash signals depends on the selected pro- tocol.

▶Check whether the protocol is set to "EtherNet/IP" or "Modbus TCP".

Network activity LED 1 and LED 3 The table below shows the meaning of the flashing signals for network activity.

Color	Status	Meaning

-	Off	No connection

Green	On	Connection with 100 [MB/s]

Yellow	On	Connection with 10 [MB/s]

Green	Flashing	Activity with 100 [MB/s]

Yellow	Flashing	Activity with 10 [MB/s]

0198441113843, V1.01, 01.2012

70	Modbus-TCP module

Image 70

Contents LXM32M Important information Table of contents Diagnostics and troubleshooting Accessories and spare parts LXM32M About this manual Further reading Introduction Fieldbus products on the networkLXM32M Qualification of personnel Before you begin safety informationIntended use Hazard categories Basic information Standards and terminology Function principle BasicsModbus TCP technology Bus topologyNetwork service Snmp Client / server modelModbus TCP protocol Structure of a Modbus messageMbap header Field Length DescriptionModbus TCP communication Connection managementModbus response to a Modbus request Excep Name Description Tion CodeReading and writing parameters Address Value4 I/O scanning to Drive Profile Lexium 4.1 I/O scanning Output Byte Meaning Data type Parameter address4.2 I/O scanning Input Bit MeaningBit Signal Factory setting InputsParameter channel Ctrl Subindex Index Function Code 3 Read Multiple Registers Modbus services Function CodeField Bytes Value Meaning Function Code 8 Diagnostics Sub-function Code Diagnostics functionFunction Code 16 Write Multiple Registers Function Code 23 ReadWrite Multiple Registers Function Code 43 Encapsulated Interface Transport Object ID Object name ValueExamples Example of Function CodeLXM32M Installation of the module InstallationDescription Order no Electrical installation Pin Signal MeaningCommissioning Commissioning the deviceFirst Setup Switching on the device Power stage supply is switched offManual / MAnu Manual Bootp / boot BootpManual assignment of the network address Dhcp / dhcP DhcpIP address Ethernet module, byte Assignment of the network address via Bootp Assignment of the network address via Dhcp Setting the transmission rate Setting the protocolSetting the gateway Set the IP address of the gateway with the parametersMaster with Word Swap Setting the master for I/O scanning Setting I/O-ScanningActivating I/O scanning Setting the mapping for I/O scanning PLC Setting the web server Setting communication monitoring for I/O scanning0198441113843, V1.01 Operation Indication of the operating state Operating statesBit Name Meaning Changing the operating state Bit Name Meaning Operating stateOperating modes Indicating and monitoring the operating modeBit Name Description Starting and changing an operating mode Bit Name DescriptionOverview of operating modes MODE+ACTIONOperating mode Jog Operating mode Electronic Gear Operating mode Profile Torque 24 hOperating mode Profile Velocity 23 hOperating mode Profile Position Operating mode Homing Operating mode Motion Sequence LXM32M6 OperationExtended settings Web serverMain menu Submenu Content User interfaceAccessing the FTP server FTP serverFDR service Fast Device Replacement LXM32M Diagnostics and troubleshooting Fieldbus communication error diagnosticsStatus LEDs Color Status MeaningColor Meaning for EtherNet/IP Meaning for Modbus TCPError indication Excep Name Description Tion Code LXM32M Accessories and spare parts CablesLXM32M Glossary Units and conversion tablesTorque TemperatureRotation Moment of inertiaTerms and Abbreviations LXM32M Index LXM32M