Schneider Electric LXM32M manual Electrical installation, Pin Signal Meaning

Page 36

4 Installation			LXM32M

4.2	Electrical installation
	Cable specifications
	Cable specifications	Shield:	Required, both ends grounded
		Shield:	Required, both ends grounded

		Twisted Pair:	Required

		PELV:	Required

		Cable composition:	8 * 0.25 mm2 (8 * AWG 22)
		Maximum cable length:	100 m

		Special features:	-

Pin assignment

▶Note the pertinent information on equipotential bonding conductors in the product manual.

▶Use pre-assembled cables to reduce the risk of wiring errors.

	Slot 3	8
	Slot 3	7
		6
		5
	8	4	A
	A	3
	A	2
	1	2
	1	1
	8	8
	B	7
	B	6	B
	1	6
	1	5
		5
		4
		3
		2
		1

Figure 5: Pin assignment

Pin	Signal	Meaning

1	Tx+	Ethernet transmit signal +
2	Tx-	Ethernet transmit signal -
3	Rx+	Ethernet receive signal +
4	-	-
5	-	-
6	Rx-	Ethernet receive signal -
7	-	-
8	-	-

0198441113843, V1.01, 01.2012

36	Modbus-TCP module

Image 36

Contents LXM32M Important information Table of contents Diagnostics and troubleshooting Accessories and spare parts LXM32M About this manual Further reading Introduction Fieldbus products on the networkLXM32M Before you begin safety information Qualification of personnelIntended use Hazard categories Basic information Standards and terminology Basics Modbus TCP technologyFunction principle Bus topologyNetwork service Snmp Client / server modelModbus TCP protocol Structure of a Modbus messageMbap header Field Length DescriptionModbus TCP communication Connection managementModbus response to a Modbus request Excep Name Description Tion CodeReading and writing parameters Address Value4 I/O scanning to Drive Profile Lexium 4.1 I/O scanning Output Byte Meaning Data type Parameter address4.2 I/O scanning Input Bit MeaningBit Signal Factory setting InputsParameter channel Ctrl Subindex Index Modbus services Function Code Function Code 3 Read Multiple RegistersField Bytes Value Meaning Function Code 8 Diagnostics Sub-function Code Diagnostics functionFunction Code 16 Write Multiple Registers Function Code 23 ReadWrite Multiple Registers Function Code 43 Encapsulated Interface Transport Object ID Object name ValueExamples Example of Function CodeLXM32M Installation Installation of the moduleDescription Order no Electrical installation Pin Signal MeaningCommissioning Commissioning the deviceFirst Setup Switching on the device Power stage supply is switched offBootp / boot Bootp Manual assignment of the network addressManual / MAnu Manual Dhcp / dhcP DhcpIP address Ethernet module, byte Assignment of the network address via Bootp Assignment of the network address via Dhcp Setting the transmission rate Setting the protocolSetting the gateway Set the IP address of the gateway with the parametersMaster with Word Swap Setting I/O-Scanning Setting the master for I/O scanningActivating I/O scanning Setting the mapping for I/O scanning PLC Setting the web server Setting communication monitoring for I/O scanning0198441113843, V1.01 Operation Operating states Indication of the operating stateBit Name Meaning Changing the operating state Bit Name Meaning Operating stateIndicating and monitoring the operating mode Operating modesBit Name Description Starting and changing an operating mode Bit Name DescriptionOverview of operating modes MODE+ACTIONOperating mode Jog Operating mode Electronic Gear Operating mode Profile Torque 24 hOperating mode Profile Velocity 23 hOperating mode Profile Position Operating mode Homing Operating mode Motion Sequence LXM32M6 OperationExtended settings Web serverMain menu Submenu Content User interfaceAccessing the FTP server FTP serverFDR service Fast Device Replacement LXM32M Diagnostics and troubleshooting Fieldbus communication error diagnosticsStatus LEDs Color Status MeaningColor Meaning for EtherNet/IP Meaning for Modbus TCPError indication Excep Name Description Tion Code LXM32M Accessories and spare parts CablesLXM32M Glossary Units and conversion tablesTemperature RotationTorque Moment of inertiaTerms and Abbreviations LXM32M Index LXM32M