JVC TK-C215VP4U/E manual Base, Fastening Screw for Dome Cover, AC 24 V/DC 12 V Power Supply Wire

Page 10

Introduction

Name of Parts (continued)

Camera (continued)

L

K

J TK-C215VP12U/E only

I

G	H

GBase

Mount the base to the ceiling, wall or electrical box before mounting the camera.

(A Pg. 21)(A Pg. 31)

H Fastening Screw for Dome Cover

This is a fastening screw for the dome cover. Use a supplied wrench to fasten/unfasten the screw.

I AC 24 V/DC 12 V Power Supply Wire

DC 12 V Input: Red (+12 V), Black (GND)

AC 24 V Input: Nonpolar

Note:

●In order to use the optional heater unit sold separately (part number KA-ZH215) with this camera an AC 24 V power supply MUST be use.

●The AC 24 V power supply should conform to the following:

U-type: Class 2 only

E-type: Isolated power supply only

●For inquiries on the heater, consult your nearby JVC dealer.

J Alarm signal cable (TK-C215VP12U/E only)

Yellow (ALARM IN), Gray (ALARM GND). (A Pg. 18)

K Protection Cover

Upon connecting the video cable please protect the BNC connection using this rubber cover.

L Video signal output connector (BNC)

(A Pg. 17)

10

Image 10

Contents TK-C215VP4U/E Instructions TK-C215VP12U/E For Customer UseIntroduction Safety Precautions For USA and CanadaDear Customer Characteristics Table of Contents Storage and Location of Use Precautions for proper use of this productOthers Note on consumable parts MaintenanceEnergy Conservation TK-C215VP12U/E onlyName of Parts CameraVideo signal output connector BNC AC 24 V/DC 12 V Power Supply WireAlarm signal cable TK-C215VP12U/E only BaseCamera Interior MemoB,+/- R/B,+/- adjustment button Setting the Switches Lens TK-C215VP4U/ERESET/SPOT RESET/SPOT button Function selection switches AGC Auto-gain control switchBLC Backlight compensation switch Sync Synchronization system selection switchWHT.BAL. ATW/MANUAL selection switch DAY/NIGHT Easy Day & Night switchB,+/- R/B, +/- adjustment button Alarm Position status indication LEDPosition Select Position Select button Alarm alarm input mode selection switch TriggerSystem Example Metal ContactDC 12 V or AC 24 V power supply cable Video signal cablesAbout Connection Cables Electrical Specifications of Alarm Input Terminals ‹ Polarity of alarm signalsRight sequence to connect and set the camera Removing the dome cover Setting the switchesSetting the switches Removing the inner domeMounting the base SetupMounting the fall prevention wire to a firm place Removing the camera unit from the baseConnect the alarm cable. TK-C215VP12U/E onlyA Pg Connecting the coaxial cable a PgConnecting the AC 24 V/DC 12 V power supply wires Cable ConnectionMounting the camera unit to the base Mounting the camera unitFill the hole with sealing material Fastening the 2 fastening screws of the camera unitInserting the silica gel supplied Adjusting the shooting direction of the camera Adjusting the video imageMounting the test monitor Adjusting the focus Adjusting the angle of view, focus and brightnessAdjusting the angle of view TK-C215VP4U/EAdjusting the brightness TK-C215VP12U/E Adjust the focusAdjust the brightness Registering home position Registering alarm position Mounting the inner dome Mounting the dome coverMounting the camera using the electrical box Following procedures are same as normal mountingMounting the base to the pipe Mounting the camera using the pipeMounting the fall prevention wire to a firm place a Pg Fastening the base to the ceilingRemoving the plug for the piping hole of the base White-spot correction Page Specifications Camera Lens General Dimensional Outline Drawing Focus chart TK-C215VP4U/E TK-C215VP12U/E Dome Camera