JVC TK-C215VP4U/E, TK-C215VP12U/E manual Cable Connection, Connecting the coaxial cable a Pg

Page 22

Installation and Connection

Cable Connection

1. Connecting the coaxial cable (A Pg. 17)

Lower the protection cover and connect the connectors. Upon connecting, cover the connectors using the protection cover.

2. Connecting the AC 24 V/DC 12 V power supply wires

2

Solder or Caulk

Note:

●To mount a heater (sold separately) to this unit, make sure to connect it to an AC 24 V supply during use.

3. Connect the alarm cable. (TK-C215VP12U/E only)(A Pg. 18)

4. Binding the AC 24 V/DC 12 V power supply wires and alarm signal wires (TK- C215VP12U/E only) with insulating tape

Make sure to bind the connecting portions of AC 24 V/DC 12 V power supply wires and alarm signal wires (TK-C215VP12U/E only) with insulating tape.

5. Wrap insulation tape around cables.

6. Storing cables

Upon connecting, push the connector into the cable storage space of the camera unit.

Note:

Protection Cover Coaxial Cable

Insulating Tape
1	Bind

3	insulating
	tape
AC 24 V/DC 12 V
Power Supply
Wire

Alarm signal Wire (TK-C215VP12 only)

4

Cable Storage

Space

●When mounting the camera to the electrical box, push the connector into the electrical box.

●While the camera unit is disconnected from the base, be extremely careful not to drop the camera unit.

*TK-C215VP12U/E is used in the above illustration

S

]

22

Image 22

Contents TK-C215VP4U/E Instructions TK-C215VP12U/E For Customer UseIntroduction Safety Precautions For USA and CanadaDear Customer Characteristics Table of Contents Storage and Location of Use Precautions for proper use of this productOthers Note on consumable parts MaintenanceEnergy Conservation TK-C215VP12U/E onlyName of Parts CameraVideo signal output connector BNC AC 24 V/DC 12 V Power Supply WireAlarm signal cable TK-C215VP12U/E only BaseCamera Interior MemoB,+/- R/B,+/- adjustment button Setting the Switches Lens TK-C215VP4U/ERESET/SPOT RESET/SPOT button Function selection switches AGC Auto-gain control switchBLC Backlight compensation switch Sync Synchronization system selection switchWHT.BAL. ATW/MANUAL selection switch DAY/NIGHT Easy Day & Night switchB,+/- R/B, +/- adjustment button Alarm Position status indication LEDPosition Select Position Select button Alarm alarm input mode selection switch TriggerSystem Example Metal ContactDC 12 V or AC 24 V power supply cable Video signal cablesAbout Connection Cables Electrical Specifications of Alarm Input Terminals ‹ Polarity of alarm signalsRight sequence to connect and set the camera Removing the dome cover Setting the switchesSetting the switches Removing the inner domeMounting the base SetupMounting the fall prevention wire to a firm place Removing the camera unit from the baseConnect the alarm cable. TK-C215VP12U/E onlyA Pg Connecting the coaxial cable a PgConnecting the AC 24 V/DC 12 V power supply wires Cable ConnectionMounting the camera unit to the base Mounting the camera unitFill the hole with sealing material Fastening the 2 fastening screws of the camera unitInserting the silica gel supplied Adjusting the shooting direction of the camera Adjusting the video imageMounting the test monitor Adjusting the focus Adjusting the angle of view, focus and brightnessAdjusting the angle of view TK-C215VP4U/EAdjusting the brightness TK-C215VP12U/E Adjust the focusAdjust the brightness Registering home position Registering alarm position Mounting the inner dome Mounting the dome coverMounting the camera using the electrical box Following procedures are same as normal mountingMounting the base to the pipe Mounting the camera using the pipeMounting the fall prevention wire to a firm place a Pg Fastening the base to the ceilingRemoving the plug for the piping hole of the base White-spot correction Page Specifications Camera Lens General Dimensional Outline Drawing Focus chart TK-C215VP4U/E TK-C215VP12U/E Dome Camera