JVC TK-C215VP12U/E, TK-C215VP4U/E manual Safety Precautions, For USA and Canada

Page 3

Safety Precautions

FOR USA AND CANADA

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash wish arrowhead symbol, within an equilateral triangle isintended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure thatmay be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert theuser to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

INFORMATION (FOR CANADA) RENSEIGNEMENT (POUR CANADA)

This Class B digital apparatus complies with Canadian ICES-003.

Cet apparéil numerique de la Classe B est conforme à la norme NMB-003 du Canada.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

AVERTISSEMENT:

POUR EVITER LES RISQUES D'INCENDIE OU D'ELECTROCUTION, NE PAS EXPOSER L'APPAREIL A L'HUMIDITE OU A LA PLUIE.

INFORMATION FOR USA

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

0Reorient or relocate the receiving antenna.

0Increase the separation between the equipment and receiver.

0Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

0Consult the dealer or an experienced radio/TV technician for help.

CAUTION

CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Due to design modifications, data given in this instruction book are subject to possible change without prior notice.

3

Image 3
Contents For Customer Use TK-C215VP4U/E Instructions TK-C215VP12U/EIntroduction For USA and Canada Safety PrecautionsDear Customer Characteristics Table of Contents Precautions for proper use of this product Storage and Location of UseOthers TK-C215VP12U/E only MaintenanceEnergy Conservation  Note on consumable partsCamera Name of PartsBase AC 24 V/DC 12 V Power Supply WireAlarm signal cable TK-C215VP12U/E only Video signal output connector BNCMemo Camera InteriorFunction selection switches AGC Auto-gain control switch Setting the Switches Lens TK-C215VP4U/ERESET/SPOT RESET/SPOT button B,+/- R/B,+/- adjustment buttonDAY/NIGHT Easy Day & Night switch Sync Synchronization system selection switchWHT.BAL. ATW/MANUAL selection switch BLC Backlight compensation switchAlarm Position status indication LED B,+/- R/B, +/- adjustment buttonPosition Select Position Select button Trigger Alarm alarm input mode selection switchMetal Contact System ExampleVideo signal cables DC 12 V or AC 24 V power supply cableAbout Connection Cables ‹ Polarity of alarm signals Electrical Specifications of Alarm Input TerminalsRight sequence to connect and set the camera Removing the inner dome Setting the switchesSetting the switches Removing the dome coverRemoving the camera unit from the base SetupMounting the fall prevention wire to a firm place Mounting the baseCable Connection Connecting the coaxial cable a PgConnecting the AC 24 V/DC 12 V power supply wires Connect the alarm cable. TK-C215VP12U/E onlyA PgFastening the 2 fastening screws of the camera unit Mounting the camera unitFill the hole with sealing material Mounting the camera unit to the baseInserting the silica gel supplied Adjusting the video image Adjusting the shooting direction of the cameraMounting the test monitor  TK-C215VP4U/E Adjusting the angle of view, focus and brightnessAdjusting the angle of view Adjusting the focusAdjusting the brightness  Registering home position Adjust the focusAdjust the brightness  TK-C215VP12U/E Registering alarm position Mounting the dome cover Mounting the inner domeFollowing procedures are same as normal mounting Mounting the camera using the electrical boxFastening the base to the ceiling Mounting the camera using the pipeMounting the fall prevention wire to a firm place a Pg Mounting the base to the pipeRemoving the plug for the piping hole of the base White-spot correction Page  Camera Specifications General  Lens Dimensional Outline Drawing Focus chart TK-C215VP4U/E TK-C215VP12U/E Dome Camera