JVC TK-C215VP12U/E, TK-C215VP4U/E manual Mounting the camera using the electrical box

Page 31

Note:

●Make sure that the dome cover is firmly fastened.

Otherwise, the humidity level may rise, which may result in fogging and even falling of the cover.

●Ensure that the fall prevention wire of the dome cover is not caught in the space between the dome cover and base. Failing to do so may cause the dust-proof and water- proof features to malfunction.

Mounting the camera using the electrical box

Mounting the base to the electrical box.

1. Setting the switches (A Pg. 20)

2. Removing the camera unit from the base (A Pg. 21)

3. Mounting the base to the electrical box

Mount the base to the electrical box by using the 2 mounting holes and 2 M4 screws.

Memo:

●M4 screws are not supplied with this product.

4 Inch square electrical box

Base

M4 Screw

4. The following procedures are same as normal mounting

●Cable Connection (A Pg. 22)

●Mounting the camera unit to the base

●(A Pg. 23)

●Adjusting Images (A Pg. 25)

●Mounting the inner dome (A Pg. 30)

●Mounting the dome cover (A Pg. 30)

31

Image 31

Contents For Customer Use TK-C215VP4U/E Instructions TK-C215VP12U/EIntroduction For USA and Canada Safety PrecautionsDear Customer Characteristics Table of Contents Storage and Location of Use Precautions for proper use of this productOthers TK-C215VP12U/E only MaintenanceEnergy Conservation Note on consumable partsCamera Name of PartsBase AC 24 V/DC 12 V Power Supply WireAlarm signal cable TK-C215VP12U/E only Video signal output connector BNCMemo Camera InteriorFunction selection switches AGC Auto-gain control switch Setting the Switches Lens TK-C215VP4U/ERESET/SPOT RESET/SPOT button B,+/- R/B,+/- adjustment buttonDAY/NIGHT Easy Day & Night switch Sync Synchronization system selection switchWHT.BAL. ATW/MANUAL selection switch BLC Backlight compensation switchB,+/- R/B, +/- adjustment button Alarm Position status indication LEDPosition Select Position Select button Trigger Alarm alarm input mode selection switchMetal Contact System ExampleDC 12 V or AC 24 V power supply cable Video signal cablesAbout Connection Cables ‹ Polarity of alarm signals Electrical Specifications of Alarm Input TerminalsRight sequence to connect and set the camera Removing the inner dome Setting the switchesSetting the switches Removing the dome coverRemoving the camera unit from the base SetupMounting the fall prevention wire to a firm place Mounting the baseCable Connection Connecting the coaxial cable a PgConnecting the AC 24 V/DC 12 V power supply wires Connect the alarm cable. TK-C215VP12U/E onlyA PgFastening the 2 fastening screws of the camera unit Mounting the camera unitFill the hole with sealing material Mounting the camera unit to the baseInserting the silica gel supplied Adjusting the shooting direction of the camera Adjusting the video imageMounting the test monitor TK-C215VP4U/E Adjusting the angle of view, focus and brightnessAdjusting the angle of view Adjusting the focusAdjusting the brightness Registering home position Adjust the focusAdjust the brightness TK-C215VP12U/E Registering alarm position Mounting the dome cover Mounting the inner domeFollowing procedures are same as normal mounting Mounting the camera using the electrical boxFastening the base to the ceiling Mounting the camera using the pipeMounting the fall prevention wire to a firm place a Pg Mounting the base to the pipeRemoving the plug for the piping hole of the base White-spot correction Page Camera Specifications General Lens Dimensional Outline Drawing Focus chart TK-C215VP4U/E TK-C215VP12U/E Dome Camera