JVC TK-C215VP12U/E manual Setting the Switches Lens TK-C215VP4U/E, RESET/SPOT RESET/SPOT button

Page 12

Introduction

Setting the Switches and the

Lens (TK-C215VP4U/E)

Set the video setting switches on the camera unit before mounting it. To set the switches, use a fine-tipped screwdriver.

A

B

		LL PHASE
		1
		1
C		2
C		4
		3
		5
		5
		6
		7
		8

RESET/[SPOT]

R

B

O

N2

4

WHT.

BAL.

F G

	D	H
	L	H
	E	IRIS
	E	LEVEL
		LEVEL
		FOCUS ADJUST

Function Selection Switch Settings Chart (Characters in bold indicate factory settings)

		OFF		ON
1	AGC	OFF		ON
2	SELECT	PHASE		WHT.BAL.
3	SYNC	LL		INT
4	WHT.BAL.	ATW		MANU
5	BLC	OFF		ON
6	DAY/NIGHT	OFF		ON
7	RESERVED		SET TO OFF
8	RESET/SPOT	RESET		SPOT

A [RESET/SPOT] RESET/SPOT button

When switch #8 is set to [RESET] position and this button is pressed, the value of the white balance or phase adjusted manually is reset to the default value.

●When switch 2 [SELECT] is set to WHT.BAL., the white balance is reset to the default value. When the switch is set to PHASE, the phase is reset to the default value.

●When switch #8 is set to SPOT:

When this button is pressed, white spots are corrected.

For instructions on correcting white spots, see AWhite-spot correctionB (A Pg. 34).

B[R/B,+/-] R/B,+/- adjustment button

This button is pressed when manually adjusting the white balance or when adjusting the vertical phase of the line lock.

The function of this button is selected using the 2 [SELECT] switch.

●When manually adjusting the white balance: Press the R button to increase the red tint and decrease the blue tint.

Press the B button to increase the blue tint and decrease the red tint.

●When adjusting the phase:

Press the + or - button to adjust the phase.

C Function selection switches

1.[AGC] Auto-gain control switch.

Setting this switch to AONB automatically increases the sensitivity even when the brightness of the subject is insufficient. (Default setting: ON)

2.[SELECT] WHT.BAL./PHASE setting switch.

WHT.BAL. :

The B [R/B,+/-] buttons are used as [R/B] adjustment buttons.

PHASE :

The B [R/B,+/-] buttons are used as [+/-] adjustment buttons.

(Default setting: WHT.BAL.)

12

Image 12

Contents TK-C215VP4U/E Instructions TK-C215VP12U/E For Customer UseIntroduction Safety Precautions For USA and CanadaDear Customer Characteristics Table of Contents Precautions for proper use of this product Storage and Location of UseOthers Maintenance Energy Conservation Note on consumable parts TK-C215VP12U/E onlyName of Parts CameraAC 24 V/DC 12 V Power Supply Wire Alarm signal cable TK-C215VP12U/E onlyVideo signal output connector BNC BaseCamera Interior MemoSetting the Switches Lens TK-C215VP4U/E RESET/SPOT RESET/SPOT buttonB,+/- R/B,+/- adjustment button Function selection switches AGC Auto-gain control switchSync Synchronization system selection switch WHT.BAL. ATW/MANUAL selection switchBLC Backlight compensation switch DAY/NIGHT Easy Day & Night switchAlarm Position status indication LED B,+/- R/B, +/- adjustment buttonPosition Select Position Select button Alarm alarm input mode selection switch TriggerSystem Example Metal ContactVideo signal cables DC 12 V or AC 24 V power supply cableAbout Connection Cables Electrical Specifications of Alarm Input Terminals ‹ Polarity of alarm signalsRight sequence to connect and set the camera Setting the switches Setting the switchesRemoving the dome cover Removing the inner domeSetup Mounting the fall prevention wire to a firm placeMounting the base Removing the camera unit from the baseConnecting the coaxial cable a Pg Connecting the AC 24 V/DC 12 V power supply wiresConnect the alarm cable. TK-C215VP12U/E onlyA Pg Cable ConnectionMounting the camera unit Fill the hole with sealing materialMounting the camera unit to the base Fastening the 2 fastening screws of the camera unitInserting the silica gel supplied Adjusting the video image Adjusting the shooting direction of the cameraMounting the test monitor Adjusting the angle of view, focus and brightness Adjusting the angle of viewAdjusting the focus TK-C215VP4U/EAdjusting the brightness Adjust the focus Adjust the brightness TK-C215VP12U/E Registering home position Registering alarm position Mounting the inner dome Mounting the dome coverMounting the camera using the electrical box Following procedures are same as normal mountingMounting the camera using the pipe Mounting the fall prevention wire to a firm place a PgMounting the base to the pipe Fastening the base to the ceilingRemoving the plug for the piping hole of the base White-spot correction Page Specifications Camera Lens General Dimensional Outline Drawing Focus chart TK-C215VP4U/E TK-C215VP12U/E Dome Camera