JVC TK-C215VP4U/E manual Setting the switches, Removing the dome cover, Removing the inner dome

Page 20

Installation and Connection

Setting the switches

Remove the dome cover, followed by setting the video image switches.

1. Removing the dome cover

Remove the dome cover by unfastening the 3 fastening screws using the wrench supplied.

Memo:

●The dome cover and base are connected with fall prevention wire.

Wrench (Supplied)

Fall Prevention

Wire

*TK-C215VP4U/E is used in the above illustration

2. Removing the inner dome

The inner dome is fastened using clips at 3 different positions. Grasp the inner dome and remove it from the clips.

Note:

●Before touching the camera unit, make sure to touch the metal surface of the [MONITOR] terminal to discharge any static electricity from your body. Static electricity may cause the camera to malfunction.

3. Setting the switches

Set the switches for video images.

(APg. 12 eSetting the Switches and the Lens (TK-C215VP4U/E)f)

(APg. 14 eSetting the Switches and the Lens (TK-C215VP12U/E)f)

			Inner
	2		Dome
	2
Clip(x 3)		3	LL PHASE
Clip(x 3)		3	1	O
			1	N 2
			2	N 2
			3	4
			4	4
			5	WHT.
			6	WHT.
			7	BAL.
			8

*TK-C215VP4U/E is used in the above illustration

20

Image 20

Contents TK-C215VP4U/E Instructions TK-C215VP12U/E For Customer UseIntroduction Safety Precautions For USA and CanadaDear Customer Characteristics Table of Contents Others Precautions for proper use of this productStorage and Location of Use Maintenance Energy Conservation Note on consumable parts TK-C215VP12U/E onlyName of Parts CameraAC 24 V/DC 12 V Power Supply Wire Alarm signal cable TK-C215VP12U/E onlyVideo signal output connector BNC BaseCamera Interior MemoSetting the Switches Lens TK-C215VP4U/E RESET/SPOT RESET/SPOT buttonB,+/- R/B,+/- adjustment button Function selection switches AGC Auto-gain control switchSync Synchronization system selection switch WHT.BAL. ATW/MANUAL selection switchBLC Backlight compensation switch DAY/NIGHT Easy Day & Night switchPosition Select Position Select button Alarm Position status indication LEDB,+/- R/B, +/- adjustment button Alarm alarm input mode selection switch TriggerSystem Example Metal ContactAbout Connection Cables Video signal cablesDC 12 V or AC 24 V power supply cable Electrical Specifications of Alarm Input Terminals ‹ Polarity of alarm signalsRight sequence to connect and set the camera Setting the switches Setting the switchesRemoving the dome cover Removing the inner domeSetup Mounting the fall prevention wire to a firm placeMounting the base Removing the camera unit from the baseConnecting the coaxial cable a Pg Connecting the AC 24 V/DC 12 V power supply wiresConnect the alarm cable. TK-C215VP12U/E onlyA Pg Cable ConnectionMounting the camera unit Fill the hole with sealing materialMounting the camera unit to the base Fastening the 2 fastening screws of the camera unitInserting the silica gel supplied Mounting the test monitor Adjusting the video imageAdjusting the shooting direction of the camera Adjusting the angle of view, focus and brightness Adjusting the angle of viewAdjusting the focus TK-C215VP4U/EAdjusting the brightness Adjust the focus Adjust the brightness TK-C215VP12U/E Registering home position Registering alarm position Mounting the inner dome Mounting the dome coverMounting the camera using the electrical box Following procedures are same as normal mountingMounting the camera using the pipe Mounting the fall prevention wire to a firm place a PgMounting the base to the pipe Fastening the base to the ceilingRemoving the plug for the piping hole of the base White-spot correction Page Specifications Camera Lens General Dimensional Outline Drawing Focus chart TK-C215VP4U/E TK-C215VP12U/E Dome Camera