JVC TK-C215VP12U/E, TK-C215VP4U/E manual Removing the plug for the piping hole of the base

Page 33

Mounting the camera using the piping hole at the side surface of the base

If the camera cannot be mounted directly to the ceiling, mount it to the pipe using the piping hole at the side surface of the base.

1. Setting the switches (A Pg. 20)

2. Dismantle the camera unit from the base and mount the fall prevention wire

(A Pg. 21)(A Pg. 9)

3. Binding the sealing tape

Bind at least 2 layers of the sealing tape to the joint of the pipe (point where the thread of the piping hole coincides with the screw hole of the pipe).

Sealing Tape

4. Removing the plug for the piping hole of the base

Loosen the mounting screw (M3 x 6 mm) using a slotted screwdriver and pull out the plug at the side of the base.

Plug for Piping Hole

Mounting

Screw

5. Mounting the removed plug for the piping hole to the piping hole at the bottom surface of the base

6. Mounting the base to the pipe

Screw the pipe into the piping hole at the side of the base.

(Piping hole: G3/4-14 UNC)

Note:

●When screwing in the pipe, make sure that not more than 12 mm (15/32 inch) of the pipe is being screwed in. Failure to do so may damage the internal components of this unit.

Plug for Piping

Hole

7. The following procedures are same as normal mounting

●Cable Connection (A Pg. 22)

●Mounting the camera unit to the base (A Pg. 23)

●Adjusting Images (A Pg. 25)

●Mounting the inner dome (A Pg. 30)

●Mounting the dome cover (A Pg. 30)

33

Image 33

Contents For Customer Use TK-C215VP4U/E Instructions TK-C215VP12U/EIntroduction For USA and Canada Safety PrecautionsDear Customer Characteristics Table of Contents Precautions for proper use of this product Storage and Location of UseOthers Energy Conservation Maintenance Note on consumable parts TK-C215VP12U/E onlyCamera Name of PartsAlarm signal cable TK-C215VP12U/E only AC 24 V/DC 12 V Power Supply WireVideo signal output connector BNC BaseMemo Camera InteriorRESET/SPOT RESET/SPOT button Setting the Switches Lens TK-C215VP4U/EB,+/- R/B,+/- adjustment button Function selection switches AGC Auto-gain control switchWHT.BAL. ATW/MANUAL selection switch Sync Synchronization system selection switchBLC Backlight compensation switch DAY/NIGHT Easy Day & Night switchAlarm Position status indication LED B,+/- R/B, +/- adjustment buttonPosition Select Position Select button Trigger Alarm alarm input mode selection switchMetal Contact System ExampleVideo signal cables DC 12 V or AC 24 V power supply cableAbout Connection Cables ‹ Polarity of alarm signals Electrical Specifications of Alarm Input TerminalsRight sequence to connect and set the camera Setting the switches Setting the switchesRemoving the dome cover Removing the inner domeMounting the fall prevention wire to a firm place SetupMounting the base Removing the camera unit from the baseConnecting the AC 24 V/DC 12 V power supply wires Connecting the coaxial cable a PgConnect the alarm cable. TK-C215VP12U/E onlyA Pg Cable ConnectionFill the hole with sealing material Mounting the camera unitMounting the camera unit to the base Fastening the 2 fastening screws of the camera unitInserting the silica gel supplied Adjusting the video image Adjusting the shooting direction of the cameraMounting the test monitor Adjusting the angle of view Adjusting the angle of view, focus and brightnessAdjusting the focus TK-C215VP4U/EAdjusting the brightness Adjust the brightness Adjust the focus TK-C215VP12U/E Registering home position Registering alarm position Mounting the dome cover Mounting the inner domeFollowing procedures are same as normal mounting Mounting the camera using the electrical boxMounting the fall prevention wire to a firm place a Pg Mounting the camera using the pipeMounting the base to the pipe Fastening the base to the ceilingRemoving the plug for the piping hole of the base White-spot correction Page Camera Specifications General Lens Dimensional Outline Drawing Focus chart TK-C215VP4U/E TK-C215VP12U/E Dome Camera