JVC TK-C215VP12U/E, TK-C215VP4U/E manual Name of Parts, Camera

Page 9

Name of Parts

Camera

A

B

CF

D

E

A Mounting hole 2

Use these when mounting the camera to the ceiling, wall or electrical box.

(A Pg. 21)(A Pg. 31)

C Mounting Screw for Fall Prevention Wire

Use this screw when mounting the fall prevention wire to this unit. (Fall prevention wire is not supplied with this product.)

Note:

●To mount the camera using the electrical box, consult the dealer from which this product is purchased or any nearby JVC dealer.

B Hole for Connecting Cable and Piping

This is a hole for drawing out the connecting cable.

This hole can also be used to mount directly to pipes. (Piping hole: G3/4-14UNC)

(A Pg. 32)

Note:

●Connect the fall prevention wire to prevent this unit from falling accidentally. The camera unit may fall if this wire is not connected.

D Dome Cover

E Inner Dome

Set the switches as well as angle of view before mounting the camera. (A Pg. 20)

F Plug for Piping Hole and Piping Hole (Side)

Use this plug when mounting directly to pipes from the side. The plug for piping hole is mounted to this hole by default. (A Pg. 33)

9

Image 9

Contents For Customer Use TK-C215VP4U/E Instructions TK-C215VP12U/EIntroduction For USA and Canada Safety PrecautionsDear Customer Characteristics Table of Contents Precautions for proper use of this product Storage and Location of UseOthers Energy Conservation Maintenance Note on consumable parts TK-C215VP12U/E onlyCamera Name of PartsAlarm signal cable TK-C215VP12U/E only AC 24 V/DC 12 V Power Supply WireVideo signal output connector BNC BaseMemo Camera InteriorRESET/SPOT RESET/SPOT button Setting the Switches Lens TK-C215VP4U/EB,+/- R/B,+/- adjustment button Function selection switches AGC Auto-gain control switchWHT.BAL. ATW/MANUAL selection switch Sync Synchronization system selection switchBLC Backlight compensation switch DAY/NIGHT Easy Day & Night switchAlarm Position status indication LED B,+/- R/B, +/- adjustment buttonPosition Select Position Select button Trigger Alarm alarm input mode selection switchMetal Contact System ExampleVideo signal cables DC 12 V or AC 24 V power supply cableAbout Connection Cables ‹ Polarity of alarm signals Electrical Specifications of Alarm Input TerminalsRight sequence to connect and set the camera Setting the switches Setting the switchesRemoving the dome cover Removing the inner domeMounting the fall prevention wire to a firm place SetupMounting the base Removing the camera unit from the baseConnecting the AC 24 V/DC 12 V power supply wires Connecting the coaxial cable a PgConnect the alarm cable. TK-C215VP12U/E onlyA Pg Cable ConnectionFill the hole with sealing material Mounting the camera unitMounting the camera unit to the base Fastening the 2 fastening screws of the camera unitInserting the silica gel supplied Adjusting the video image Adjusting the shooting direction of the cameraMounting the test monitor Adjusting the angle of view Adjusting the angle of view, focus and brightnessAdjusting the focus TK-C215VP4U/EAdjusting the brightness Adjust the brightness Adjust the focus TK-C215VP12U/E Registering home position Registering alarm position Mounting the dome cover Mounting the inner domeFollowing procedures are same as normal mounting Mounting the camera using the electrical boxMounting the fall prevention wire to a firm place a Pg Mounting the camera using the pipeMounting the base to the pipe Fastening the base to the ceilingRemoving the plug for the piping hole of the base White-spot correction Page Camera Specifications General Lens Dimensional Outline Drawing Focus chart TK-C215VP4U/E TK-C215VP12U/E Dome Camera