Panasonic WV-NM100 operating instructions Adjustment of the brightness of the motion picture

Page 35

How to Operate

If the preparations have been completed, you can begin the operation from the "Basic setup" page.

Screenshot 1

Begin the operation from the "Basic setup" page.

Screenshot 2

STEP1

Click the [Control] button.

STEP2

To display the motion picture of the selected camera, click the [Live-ON] button.

To quit displaying the motion picture of the selected camera, click the [STOP] button. The motion picture disappears.

On this page, you can also operate the camera and adjust the motion picture.

Panning and tilting

The "Control" page appears. The motion picture of the cam- era is displayed.

Notes

•If the preparations have been completed, start up the browser and display the “Top Menu” page of the desired camera. The camera picture appears on the “Top Menu” page.

•The port number for the MPEG-4 streaming is set to 5004. If another application uses this port, change the port number to another even-numbered port number.

•To switch the currently monitored picture to another cam- era picture, click the [STOP] button to stop displaying the currently monitored picture. Then, enter the IP address of the desired camera in the “Address” box of the browser to monitor the desired camera picture.

Click the arrow buttons (up / down / right / left) to adjust the horizontal and vertical position. The center of the box surrounded by the arrow buttons (the point where the horizontal line and the vertical line cross) is the current position of the camera.

If you click inside the box surrounded by the arrow buttons, you can pan and tilt the camera wider than by clicking the arrow buttons.

Image capture size

Click one of the motion picture resolution but- tons (CIF (352 x 288) / QCIF (176 x 144)) to dis- play the motion picture with the desired resolu- tion.

Adjustment of the brightness of the motion picture

Click the buttons to adjust the brightness of the motion picture. The left end button (–) is the darkest and the right end button (+) is the brightest.

Image Size

Click one of the buttons (x1.0 / x1.5 / x2.0) to select the desired motion picture size.

When the picture is magnified, the quality of the picture may be decreased.

AUX

Click one of the buttons (High/Low) to set the status of the AUX output connector. (Refer to p. 53 for details.)

35

Image 35

Contents Operating Instructions English Version Important Safety Instructions Contents Advanced Settings for Operation mode Preface FeaturesDo not aim the camera at bright light sources PrecautionsMPEG-4 plug-in is exclusive to Internet Explorer PlatformTrademarks and Registered Trademarks Rear View Inside of the connector coverFront View Installations Required cable ConnectionsConnection example LAN Using with an Intranet LAN Connection typeRequired hardware Using via the Internet Connection typePreparations for the Setup SetupItems included in the software Setup with the Provided Panasonic IP Setup SoftwareDhcp DNS Using Windows 98 SE Network Setup of the PCScreenshot Using Windows Screenshot Using Windows XP Category View Network Connections window appears Network Setup of the Camera Basic setup page appears Click the Advanced setup button WAN Connection type Description of the parameter Bootp Installation of the MPEG-4 Plug-in Basic Settings Camera position Power/Link/Access LEDCharacters for Camera name Up to 32 char Hour, minute and secondQuality of image Browsing PicturesMonitoring a Still Picture of a Single Camera Image capture sizeOne time pan Adjustment of the brightness of the picturePanning and tilting Image SizeMonitoring the Motion Picture of a Single Camera Adjustment of the brightness of the motion picture Monitoring Still Pictures of Multiple Cameras Operation mode page of Advanced setup appears How to Operate Monitoring the Picture of a Camera in a Preset Position Browsing Pictures Saving the Currently Monitored Picture on the PC Motion Detector Function Action when Motion is DetectedInform by sending e-mails Detecting Motion in the Monitored Area Alarm type External alarm inputPre-alarm Post-alarmSetting of the Motion Detection Area Alarm page appears To view the previous or next picture automatically Viewing the Picture Stored in the CameraTransferring Pictures to the Server Mode PasswordDate & Time Non alarm transmission Check onDirectory File nameTransferring Pictures to the Server when Motion is Detected Other Functions Alarm Connector and AUX Output ConnectorCustomizing the Contents of the Alarm Mail Advanced Settings for Operation mode Advanced SettingsRefresh interval Operation mode selectionMPEG-4 mode setup Bandwidth controlAdjusting the Picture PAN / Tilt calibration Hold SharpnessSettings for the Host Authentication Host address Access levelSettings for the User Authentication Example admin System Settings NTP port Time adjustmentSynchronization with NTP server Time is adjust Time setup year-month-day hourminsecDefault setting for Password Default setting for Host name WV-NM100 User nameDefault setting for User name Characters for PasswordSnmp Settings Community name Default setting for Community name public Equipment nameDefault setting for Equipment name Default setting for LocationFirmware Upgrade Using HelpPossible cause / Possible solution TroubleshootingIf the camera and the PC are connected in a Different subnet If the camera and the PC are connected Same subnetIf Internet Explorer is used If Netscape Communicator is usedCamera SpecificationsTerm Explanation Glossary of TermsTerm N1102-1013 V8QA6036BN