Panasonic WV-NM100 operating instructions Motion Detector Function, Action when Motion is Detected

Page 42

DETECTING MOTION IN THE MONITORED AREA

When motion is detected in the monitored area, "Alarm" appears on the monitor screen. Simultaneously, you can save the picture of the alarmed area and send an alarm mail by e-mail (motion detector function).

You can also automatically transfer the saved image to the server.

To activate these functions, complete the setting of the "Alarm" page or the "FTP client" page in advance.

Notes

•In case a sensor is connected to the alarm connector of the camera, the functions above are available when the sensor detects motion.

•To reset an alarm, click "Alarm" on the monitor screen.

Motion Detector Function

By using the motion detector function, the alarm signal is sent when motion (changes in the brightness level) is detected in the designated area. With this camera, you can save the picture of the designated area or send an alarm mail when motion is detected.

Set the detection area and the other conditions required for the motion detector function on the "VMD area" page.

! Important

The motion detector function is available only when "JPEG" is selected for the "Operation mode selection" on the "Operating mode" page of "Advanced setup". When the motion detector function is activated, the speed of loading still pictures (JPEG) may become slower. The motion detector function does not work when "MPEG-4" is selected.

Action when Motion is Detected

By setting the motion detector function, you can set the camera to activate the following operations when motion (changes in the brightness level) is detected in the designated area.

•When motion is detected, "Alarm" appears on the monitor screen as shown in screenshot below.

"Alarm" will disappear by clicking on it.

Note

The camera checks the alarm status and reloads the browser page by the minute or when the reload but- ton is pressed. Therefore, approximately a minute delay at the maximum may occur until "Alarm" appears on the browser after an alarm occurred.

• You can save the picture of the area where motion is detected on the camera.

Number of pictures you can save: 30 pictures max. per 1 alarm (You can set the number of images to be saved up to 20 pictures for pre-alarm and up to 20 pictures for post-alarm, but the total number of images to be saved should be 30 pictures max.)

Maximum number of pictures saved: Up to 60 pictures without reference to sizes.

The older pictures will automatically be deleted if the number of the pictures exceeds 60 pictures.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Operating Instructions English Version Important Safety Instructions Contents Advanced Settings for Operation mode Features PrefacePrecautions Do not aim the camera at bright light sourcesPlatform MPEG-4 plug-in is exclusive to Internet ExplorerTrademarks and Registered Trademarks Inside of the connector cover Front ViewRear View Installations Connections Connection exampleRequired cable Using with an Intranet LAN Connection type LANUsing via the Internet Connection type Required hardwareSetup Preparations for the SetupSetup with the Provided Panasonic IP Setup Software Items included in the softwareDhcp DNS Network Setup of the PC Using Windows 98 SEScreenshot Using Windows Screenshot Using Windows XP Category View Network Connections window appears Network Setup of the Camera Basic setup page appears Click the Advanced setup button WAN Connection type Description of the parameter Bootp Installation of the MPEG-4 Plug-in Basic Settings Hour, minute and second Power/Link/Access LEDCharacters for Camera name Up to 32 char Camera positionImage capture size Browsing PicturesMonitoring a Still Picture of a Single Camera Quality of imageImage Size Adjustment of the brightness of the picturePanning and tilting One time panMonitoring the Motion Picture of a Single Camera Adjustment of the brightness of the motion picture Monitoring Still Pictures of Multiple Cameras Operation mode page of Advanced setup appears How to Operate Monitoring the Picture of a Camera in a Preset Position Browsing Pictures Saving the Currently Monitored Picture on the PC Action when Motion is Detected Motion Detector FunctionInform by sending e-mails Detecting Motion in the Monitored Area Post-alarm External alarm inputPre-alarm Alarm typeSetting of the Motion Detection Area Alarm page appears Viewing the Picture Stored in the Camera To view the previous or next picture automaticallyTransferring Pictures to the Server Password ModeFile name Non alarm transmission Check onDirectory Date & TimeTransferring Pictures to the Server when Motion is Detected Alarm Connector and AUX Output Connector Customizing the Contents of the Alarm MailOther Functions Advanced Settings Advanced Settings for Operation modeBandwidth control Operation mode selectionMPEG-4 mode setup Refresh intervalAdjusting the Picture Hold Sharpness PAN / Tilt calibrationSettings for the Host Authentication Access level Host addressSettings for the User Authentication Example admin System Settings Time setup year-month-day hourminsec Time adjustmentSynchronization with NTP server Time is adjust NTP portCharacters for Password Default setting for Host name WV-NM100 User nameDefault setting for User name Default setting for PasswordSnmp Settings Default setting for Location Default setting for Community name public Equipment nameDefault setting for Equipment name Community nameUsing Help Firmware UpgradeTroubleshooting Possible cause / Possible solutionIf the camera and the PC are connected Same subnet If the camera and the PC are connected in a Different subnetIf Netscape Communicator is used If Internet Explorer is usedSpecifications CameraGlossary of Terms Term ExplanationTerm N1102-1013 V8QA6036BN
Top Page Image Contents