Panasonic WV-NM100 operating instructions Dhcp DNS

Page 17

Screenshot 2

The setup window appears.

STEP4

Set parameters for each item. "IP Address"

"Subnet Mask" "Default Gateway" "HTTP Port"

Enter parameters depending on your environ- ment.

For further information about the parameters, refer to pages 27-28.

"DHCP"

"DNS"

Click the [Enable] radio button when using the DHCP and the DNS.

When using the DNS function, enter the “Primary DNS Server address” and the “Secondary DNS Server address”.

Notes

• If DHCP is enabled although there is no DHCP server in the network, check “Disable” for DHCP in the “Panasonic IP Setup” window.

• If DHCP is enabled, and the DHCP server has not assigned an IP address yet, “0.0.0.0” is displayed for the IP address. The IP address of the camera will be displayed after the DHCP server assigns one to the camera.

STEP5

Click the [SET] button after completing the set- ting.

! Important

It takes around 20 seconds to complete the settings of the camera after the [SET] button is pressed. If the AC adapter or the Ethernet cable is detached before the settings are com- pleted, the settings may not be performed cor- rectly.

17

Image 17

Contents Operating Instructions English Version Important Safety Instructions Contents Advanced Settings for Operation mode Preface FeaturesDo not aim the camera at bright light sources PrecautionsMPEG-4 plug-in is exclusive to Internet Explorer PlatformTrademarks and Registered Trademarks Rear View Inside of the connector coverFront View Installations Required cable ConnectionsConnection example LAN Using with an Intranet LAN Connection typeRequired hardware Using via the Internet Connection typePreparations for the Setup SetupItems included in the software Setup with the Provided Panasonic IP Setup SoftwareDhcp DNS Using Windows 98 SE Network Setup of the PCScreenshot Using Windows Screenshot Using Windows XP Category View Network Connections window appears Network Setup of the Camera Basic setup page appears Click the Advanced setup button WAN Connection type Description of the parameter Bootp Installation of the MPEG-4 Plug-in Basic Settings Characters for Camera name Up to 32 char Power/Link/Access LEDHour, minute and second Camera positionMonitoring a Still Picture of a Single Camera Browsing PicturesImage capture size Quality of imagePanning and tilting Adjustment of the brightness of the pictureImage Size One time panMonitoring the Motion Picture of a Single Camera Adjustment of the brightness of the motion picture Monitoring Still Pictures of Multiple Cameras Operation mode page of Advanced setup appears How to Operate Monitoring the Picture of a Camera in a Preset Position Browsing Pictures Saving the Currently Monitored Picture on the PC Motion Detector Function Action when Motion is DetectedInform by sending e-mails Detecting Motion in the Monitored Area Pre-alarm External alarm inputPost-alarm Alarm typeSetting of the Motion Detection Area Alarm page appears To view the previous or next picture automatically Viewing the Picture Stored in the CameraTransferring Pictures to the Server Mode PasswordDirectory Non alarm transmission Check onFile name Date & TimeTransferring Pictures to the Server when Motion is Detected Other Functions Alarm Connector and AUX Output ConnectorCustomizing the Contents of the Alarm Mail Advanced Settings for Operation mode Advanced SettingsMPEG-4 mode setup Operation mode selectionBandwidth control Refresh intervalAdjusting the Picture PAN / Tilt calibration Hold SharpnessSettings for the Host Authentication Host address Access levelSettings for the User Authentication Example admin System Settings Synchronization with NTP server Time is adjust Time adjustmentTime setup year-month-day hourminsec NTP portDefault setting for User name Default setting for Host name WV-NM100 User nameCharacters for Password Default setting for PasswordSnmp Settings Default setting for Equipment name Default setting for Community name public Equipment nameDefault setting for Location Community nameFirmware Upgrade Using HelpPossible cause / Possible solution TroubleshootingIf the camera and the PC are connected in a Different subnet If the camera and the PC are connected Same subnetIf Internet Explorer is used If Netscape Communicator is usedCamera SpecificationsTerm Explanation Glossary of TermsTerm N1102-1013 V8QA6036BN