Directed Audio XTR2504, XTR5004 owner manual End Panel Layouts

Page 4

End Panel Layouts

XTR2504 and XTR5004

 

 

Figure 1

 

 

 

Figura 1

1

2 3 4 5 9 10 11

12

Abbildung 1

6

7

8

13

14

15

1.Speakers - channels 1 and 2

2.Bass Boost - continuously adjusts from 0 to 18dB of boost cen- tered at 45Hz

3.Gain Control (Channels 1 & 2) - continuous adjustment for full power output

4.RCA Input (Channels 1 & 2) - accepts Low Level RCA Inputs (400mV-8V) from a head unit, preamplifier, or equalizer.. XTR amplifiers can also accepts High Level Speaker Inputs (200mV-4V) from an OEM stereo.. These inputs are configured by the Input Mode switch position (refer to item 6)

5.RCA Line Output - provides easy connection to additional ampli- fiers.. Note that some OEM stereo headunits may sense the attached load and may turn off their speaker outputs if expected

load conditions aren’t achieved

6.Input Mode (Channels 1 & 2) - when the switch is out, the ampli- fier will accept speaker level and high output RCA connections.. When this switch is in, it provides extra sensitivity for lower input voltage RCA (refer to item 4)

7.X-Over (cross-over channels 1 & 2) - activates LPF (low pass crossover), FLAT (all pass), or HPF (high pass crossover) selection switch

8.X-Over Frequency Control (channels 1 & 2) - FLAT (all pass) adjusts the frequency (50Hz–2000Hz) of the crossover for the HPF (High-Pass Frequency Control) and the LPF (Low-Pass Frequency Control) variable control

9.RCA Input (Channels 3 & 4) - see item 4 definition

10.Gain Control (Channels 3 & 4) - see item 3 definition

11.Bass Boost (Channels 3 & 4) - see item 2 definition

12.Speakers - channels 3 and 4

13.X-Over Frequency Control (Channels 3 & 4) - see item 8 defini- tion

14.X-Over (cross-over, channels 3 & 4) - see item 7 definition

15.Input Mode (Channels 3 & 4) - see item 6 definition

© 2008 Directed Electronics. All rights reserved.

3

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Amplifier Contents Introduction End Panel Layouts CEA Specifications Specifications Signal Input and Output Configurations Line Output ConfigurationsInternal Crossover Configurations, Flat full range Crossover SwitchHigh-Pass Crossover Adjusting Bass BoostInfinite Baffle Subsonic is set at 20Hz Sealed Example High-Pass Set at 20Hz Sealed Example High-Pass Set at 30HzPower Connections Speaker Connections XTR2504 and XTR5004Four Channel Stereo Configuration Tri-Mode Six Channel Configuration General Precautions and Installation Tips Choosing Mounting LocationsPassenger Compartment Trunk CompartmentTools of the Trade Step By Step Installation Testing the System Adjusting the Sound of the SystemAmplifier Visual Troubleshooting Amplifier Top Plate Troubleshooting Tips Symptom Probable Cause Action To TakeSymptom Probable Cause Directed Electronics. All rights reserved Français Disposition DES Panneaux LatérauxCEA Specifications Caractéristiques Techniques Réglages DE L’AMPLIFICATEUR Filtre passe-bas Filtre passe-hautRéglage du renforcement des graves Réglage passe-haut à 20 Hz dans le cas d’un cais- son closRaccordement DE L’AMPLIFICATEUR Configuration à trois canaux Configuration tri-mode six canauxInstallation DE L’AMPLIFICATEUR Choix des emplacements de montagePrécautions générales et conseils d’installation HabitacleOutillage requis Installation pas à pas Essai du système Réglage ET Résolution DES ProblèmesRéglage du son du système Résolution visuelle des problèmes de l’amplificateur Plaque supérieure de l’amplificateur Conseils de dépannage Symptôme Cause probable InterventionFrançais Symptôme Cause probable Español Disposiciones DEL Panel DE ExtremoEspecificaciones DE LA CEA THD+NEspecificaciones Configuraciones DEL Amplificador Crossover de pasabajas Crossover de pasaaltasAjuste del refuerzo de bajos Bafle infinito, filtro subsónico en 20 HzConfiguración en puente de dos canales Configuración estereofónica de cuatro canalesCableado DEL Amplificador Conexiones de altavoces del XTR2504 y del XTR5004Configuración de tres canales Configuración de modalidad triple de seis canalesInstalación DEL Amplificador Selección de ubicaciones de montajeCompartimiento de pasajeros MaleteroHerramientas DEL Oficio Instalación paso a paso Configuración Y Detección Y Reparación DE Averías Prueba del sistemaDetección y reparación visual de averías del ampli- ficador Placa superior del amplificador Sugerencias de detección y reparación de averías Síntoma Causa probable Medidas a tomarEspañol Síntoma Causa probable Layout DER Endplatten Eingangsmodus Kanäle 3 und 4 Definition siehe PunktCEA-DATEN Technische Daten Verstärkereinstellungen Hochpass-Crossover Einstellung des Bass-BoostUnendliche Schallwand, Subsonic auf 20 Hz einges- tellt Beispiel Geschlossenes Gehäuse, Hochpassfilter bei 20 HzVerstärkerverkabelung Beispiel Geschlossenes Gehäuse, Hochpassfilter bei 30 HzStromanschlüsse für den XTR2504 und XTR5004 Lautsprecheranschlüsse XTR2504 und XTR5004Zweikanal-Brückenkonfiguration Vierkanal-StereokonfigurationDreikanal-Konfiguration Dreimodus-SechskanalbetriebVerstärkerinstallation Allgemeine Vorsichts- und InstallationshinweiseWahl der Einbaustelle FahrgastraumWerkzeuge Schrittweise Installation Systemtest Einstellung UND ProblemlösungSystemsound einstellen Visuelle Anzeige von Problemen mit dem Verstärker Obere Platte des Verstärkers Problemlösungen Symptom Mögliche Ursache LösungSymptom Mögliche Ursache LösungDirected Electronics. Alle Rechte vorbehalten Italiano Layout DEI Pannelli TerminaliSpecifiche CEA Dati Tecnici Configurazione dei segnali d’ingresso e di uscita Configurazioni delle uscite di lineaImpostazioni DELL’AMPLIFICATORE Guadagno d’ingressoCrossover passa-alto Crossover passa-bassoRegolazione dell’amplificazione dei bassi Configurazione a cablaggio in parallelo con due canali Configurazione stereo a quattro canaliCablaggio DELL’AMPLIFICATORE Connessioni per l’alimentazioneConfigurazione a tre canali Configurazione a sei canali in modalità triplaScelta del punto di installazione Precauzioni generali e suggerimenti per l’installazioneNstallazione DELL’AMPLIFICATORE AbitacoloCorredo per l’installazione Procedura di installazione Prova dell’impianto Impostazione E Soluzione DEI ProblemiRegolazione dell’audio dell’impianto Spie dell’amplificatore Piastra superiore dell’amplificatore Soluzione dei problemi Sintomo Causa probabile Intervento necessarioItaliano Sintomo Causa probabile Layouts DOS Painéis Controle de Ganho canais 3 e 4 ver a definição no itemEspecificações DA CEA Especificações Ajustes do Amplificador Crossover passa-alta Sonoflector subsônico infinito é ajustado a 20 HzExemplo de caixa selada com passa-alta ajustado a 20 Hz Exemplo de caixa selada com passa-alta ajustado a 30HzConfiguração em ponte de dois canais Configuração estéreo de quatro canaisConexão DOS Cabos do Amplificador Conexões elétricasConfiguração de três canais Configuração trimodal de seis canaisInstalação do Amplificador Escolha de locais de instalaçãoCabine de passageiros Porta-malasFerramentas Instalação passo a passo Como testar o sistema Ajuste E Resolução DE ProblemasComo ajustar o som do sistema Identificação visual de problemas com o amplifi- cador Placa superior do amplificador Sugestões para resolução de problemas Problema Provável causa Medida a ser tomadaInterno deste manual Directed Electronics. Todos os direitos reservados 100 Warranty

XTR5004, XTR2504 specifications

The Directed Audio XTR2504 and XTR5004 are premium amplifiers designed for audio enthusiasts seeking an exceptional listening experience. These models are part of Directed's XTR line, which is known for its innovative technology and high performance, catering to both car audio and home audio applications.

One of the main features of the XTR2504 is its compact design, which allows it to fit in a variety of installation locations without compromising on power. The amplifier is rated at 250 watts RMS, providing ample power to drive mid-range and high-frequency speakers. It boasts a 4-channel output configuration, making it suitable for multi-speaker setups and offering flexibility for system customization.

The XTR5004 takes performance a step further, delivering an impressive 500 watts RMS. This model is ideal for larger setups or for users who require additional power to energize larger speakers and subwoofers. Both models utilize high-efficiency class D amplification technology, which minimizes power consumption while maximizing output. This efficiency translates to less heat generation, allowing for prolonged use without the risk of overheating.

One of the standout technologies featured in these amplifiers is their advanced signal processing capabilities. Both the XTR2504 and XTR5004 come equipped with variable high-pass and low-pass filters, allowing users to tailor the output frequency range according to their specific needs. This feature is crucial for optimizing sound quality, ensuring that each speaker operates within its optimal range, leading to a clearer and more balanced audio experience.

The amplifiers also incorporate a robust thermal management system, including built-in protection mechanisms that prevent damage from overheating or short circuits. This attention to durability and reliability makes the XTR2504 and XTR5004 ideal choices for both competitive audio setups and casual listening environments.

Additional characteristics include a sleek, modern design featuring a durable chassis that can withstand the rigors of installation in car environments. The amplifiers feature high-quality RCA inputs and remote gain control options for user convenience.

In summary, the Directed Audio XTR2504 and XTR5004 amplifiers exemplify cutting-edge technology in the realm of audio performance. With their powerful output, efficient design, and customizable features, these models are designed to provide an immersive audio experience that will satisfy even the most discerning audiophiles.
Top Page Image Contents