Directed Audio XTR5004 Signal Input and Output Configurations, Input Gain, Crossover Switch

Page 7

Amplifier Settings

Signal Input and Output Configurations

The input section of the amplifier consists of gain controls, high pass and low pass crossovers controls, Bass Boost control and RCA inputs and outputs.. The input section makes it easy to adapt this amplifier to most system configurations..

frequencies higher than recommended will not cause damage and may provide superior sonic results depending on your system’s perfor- mance goals.. Refer to your loudspeaker owner’s manual for assistance in choosing the proper crossover frequencies for your system..

WARNING! DO NOT set crossover frequencies lower than the speakers recommended operating range.. This can cause driver failure that is not covered by the manufacturer’s warranty..

Input Gain

These Orion amplifiers have level adjustments to allow for easy inte- gration with any source unit.. The input sensitivity can be adjusted from 200mV to 8V.. Refer to Testing the System and Adjusting the Sound of the System sections of this guide for detailed instructions on setting the gain..

Line Output Configurations

The line outputs on Orion amplifiers offer easy system expansion and can be used to route signal from the RCA line outputs to the next Orion amplifier’s RCA line inputs in the signal chain..

Internal Crossover Configurations, Flat (full range)

The crossover section of the Orion XTR2504 and XTR5004 amplifiers are continuously variable and extremely flexible..

When using Orion loudspeakers, minor deviations from the recom- mended frequency ranges can provide superior results depending on your speaker locations and your vehicle acoustics.. Setting crossover

Crossover Switch

Controls the type of filter for the onboard active crossover.. The Orion XTR2504 and XTR5004 have a switch for the selectable crossover..

Full position does not attenuate any frequencies and is for full range speaker systems..

High attenuates low frequencies and is used for mid-range speak- ers and tweeters..

Low attenuates high frequencies and is used for subwoofer speakers..

Low-Pass Crossover

When the switch is to the center (FULL position), the low-pass cross- over is bypassed.. When the switch is to the left, the low-pass crossover is active.. The low-pass crossover is continuously variable from 50Hz to 2000Hz..

© 2008 Directed Electronics. All rights reserved.

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Amplifier Contents Introduction End Panel Layouts CEA Specifications Specifications Crossover Switch Signal Input and Output ConfigurationsLine Output Configurations Internal Crossover Configurations, Flat full rangeHigh-Pass Crossover Adjusting Bass BoostInfinite Baffle Subsonic is set at 20Hz Sealed Example High-Pass Set at 30Hz Sealed Example High-Pass Set at 20HzSpeaker Connections XTR2504 and XTR5004 Power ConnectionsFour Channel Stereo Configuration Tri-Mode Six Channel Configuration Trunk Compartment General Precautions and Installation TipsChoosing Mounting Locations Passenger CompartmentTools of the Trade Step By Step Installation Adjusting the Sound of the System Testing the SystemAmplifier Visual Troubleshooting Amplifier Top Plate Symptom Probable Cause Action To Take Troubleshooting TipsSymptom Probable Cause Directed Electronics. All rights reserved Disposition DES Panneaux Latéraux FrançaisCEA Specifications Caractéristiques Techniques Réglages DE L’AMPLIFICATEUR Réglage passe-haut à 20 Hz dans le cas d’un cais- son clos Filtre passe-basFiltre passe-haut Réglage du renforcement des gravesRaccordement DE L’AMPLIFICATEUR Configuration tri-mode six canaux Configuration à trois canauxHabitacle Installation DE L’AMPLIFICATEURChoix des emplacements de montage Précautions générales et conseils d’installationOutillage requis Installation pas à pas Essai du système Réglage ET Résolution DES ProblèmesRéglage du son du système Résolution visuelle des problèmes de l’amplificateur Plaque supérieure de l’amplificateur Symptôme Cause probable Intervention Conseils de dépannageFrançais Symptôme Cause probable Disposiciones DEL Panel DE Extremo EspañolTHD+N Especificaciones DE LA CEAEspecificaciones Configuraciones DEL Amplificador Bafle infinito, filtro subsónico en 20 Hz Crossover de pasabajasCrossover de pasaaltas Ajuste del refuerzo de bajosConexiones de altavoces del XTR2504 y del XTR5004 Configuración en puente de dos canalesConfiguración estereofónica de cuatro canales Cableado DEL AmplificadorConfiguración de modalidad triple de seis canales Configuración de tres canalesMaletero Instalación DEL AmplificadorSelección de ubicaciones de montaje Compartimiento de pasajerosHerramientas DEL Oficio Instalación paso a paso Prueba del sistema Configuración Y Detección Y Reparación DE AveríasDetección y reparación visual de averías del ampli- ficador Placa superior del amplificador Síntoma Causa probable Medidas a tomar Sugerencias de detección y reparación de averíasEspañol Síntoma Causa probable Eingangsmodus Kanäle 3 und 4 Definition siehe Punkt Layout DER EndplattenCEA-DATEN Technische Daten Verstärkereinstellungen Beispiel Geschlossenes Gehäuse, Hochpassfilter bei 20 Hz Hochpass-CrossoverEinstellung des Bass-Boost Unendliche Schallwand, Subsonic auf 20 Hz einges- telltLautsprecheranschlüsse XTR2504 und XTR5004 VerstärkerverkabelungBeispiel Geschlossenes Gehäuse, Hochpassfilter bei 30 Hz Stromanschlüsse für den XTR2504 und XTR5004Dreimodus-Sechskanalbetrieb Zweikanal-BrückenkonfigurationVierkanal-Stereokonfiguration Dreikanal-KonfigurationFahrgastraum VerstärkerinstallationAllgemeine Vorsichts- und Installationshinweise Wahl der EinbaustelleWerkzeuge Schrittweise Installation Systemtest Einstellung UND ProblemlösungSystemsound einstellen Visuelle Anzeige von Problemen mit dem Verstärker Obere Platte des Verstärkers Symptom Mögliche Ursache Lösung ProblemlösungenLösung Symptom Mögliche UrsacheDirected Electronics. Alle Rechte vorbehalten Layout DEI Pannelli Terminali ItalianoSpecifiche CEA Dati Tecnici Guadagno d’ingresso Configurazione dei segnali d’ingresso e di uscitaConfigurazioni delle uscite di linea Impostazioni DELL’AMPLIFICATORECrossover passa-alto Crossover passa-bassoRegolazione dell’amplificazione dei bassi Connessioni per l’alimentazione Configurazione a cablaggio in parallelo con due canaliConfigurazione stereo a quattro canali Cablaggio DELL’AMPLIFICATOREConfigurazione a sei canali in modalità tripla Configurazione a tre canaliAbitacolo Scelta del punto di installazionePrecauzioni generali e suggerimenti per l’installazione Nstallazione DELL’AMPLIFICATORECorredo per l’installazione Procedura di installazione Prova dell’impianto Impostazione E Soluzione DEI ProblemiRegolazione dell’audio dell’impianto Spie dell’amplificatore Piastra superiore dell’amplificatore Sintomo Causa probabile Intervento necessario Soluzione dei problemiItaliano Sintomo Causa probabile Controle de Ganho canais 3 e 4 ver a definição no item Layouts DOS PainéisEspecificações DA CEA Especificações Ajustes do Amplificador Exemplo de caixa selada com passa-alta ajustado a 30Hz Crossover passa-altaSonoflector subsônico infinito é ajustado a 20 Hz Exemplo de caixa selada com passa-alta ajustado a 20 HzConexões elétricas Configuração em ponte de dois canaisConfiguração estéreo de quatro canais Conexão DOS Cabos do AmplificadorConfiguração trimodal de seis canais Configuração de três canaisPorta-malas Instalação do AmplificadorEscolha de locais de instalação Cabine de passageirosFerramentas Instalação passo a passo Como testar o sistema Ajuste E Resolução DE ProblemasComo ajustar o som do sistema Identificação visual de problemas com o amplifi- cador Placa superior do amplificador Problema Provável causa Medida a ser tomada Sugestões para resolução de problemasInterno deste manual Directed Electronics. Todos os direitos reservados 100 Warranty

XTR5004, XTR2504 specifications

The Directed Audio XTR2504 and XTR5004 are premium amplifiers designed for audio enthusiasts seeking an exceptional listening experience. These models are part of Directed's XTR line, which is known for its innovative technology and high performance, catering to both car audio and home audio applications.

One of the main features of the XTR2504 is its compact design, which allows it to fit in a variety of installation locations without compromising on power. The amplifier is rated at 250 watts RMS, providing ample power to drive mid-range and high-frequency speakers. It boasts a 4-channel output configuration, making it suitable for multi-speaker setups and offering flexibility for system customization.

The XTR5004 takes performance a step further, delivering an impressive 500 watts RMS. This model is ideal for larger setups or for users who require additional power to energize larger speakers and subwoofers. Both models utilize high-efficiency class D amplification technology, which minimizes power consumption while maximizing output. This efficiency translates to less heat generation, allowing for prolonged use without the risk of overheating.

One of the standout technologies featured in these amplifiers is their advanced signal processing capabilities. Both the XTR2504 and XTR5004 come equipped with variable high-pass and low-pass filters, allowing users to tailor the output frequency range according to their specific needs. This feature is crucial for optimizing sound quality, ensuring that each speaker operates within its optimal range, leading to a clearer and more balanced audio experience.

The amplifiers also incorporate a robust thermal management system, including built-in protection mechanisms that prevent damage from overheating or short circuits. This attention to durability and reliability makes the XTR2504 and XTR5004 ideal choices for both competitive audio setups and casual listening environments.

Additional characteristics include a sleek, modern design featuring a durable chassis that can withstand the rigors of installation in car environments. The amplifiers feature high-quality RCA inputs and remote gain control options for user convenience.

In summary, the Directed Audio XTR2504 and XTR5004 amplifiers exemplify cutting-edge technology in the realm of audio performance. With their powerful output, efficient design, and customizable features, these models are designed to provide an immersive audio experience that will satisfy even the most discerning audiophiles.
Top Page Image Contents