Directed Audio XTR2504, XTR5004 owner manual Specifications

Page 6

Specifications

Amplifier Section

XTR2504

XTR5004

Power Output 4Ω (Watts) *

50 x 4

80 x 4

 

 

 

Power Output 2Ω (Watts)

70 x 4

125 x 4

**

 

 

 

 

 

Power Output 4Ω (Watts)

250 x 1

500 x 1

Bridged

 

 

 

 

 

Amplifier Efficiency

> 60% into 2Ω load

> 60% into 2Ω load

 

at max.. power

at max.. power

 

 

 

Signal to Noise ratio at

>95dB

>95dB

rated output power and

 

 

lowest impedance

 

 

 

 

 

Externally Bridgeable

No

No

 

 

 

Distortion at Rated Power

0..05% THD+N

0..05% THD+N

 

 

 

Frequency Response

20 Hz to 20 kHz +/-

20 Hz to 20 kHz +/-

 

2..5dB

2..5dB

 

 

 

Linear Bandwidth

20 Hz to 30 kHz

20 Hz to 30 kHz

 

+/- 3dB

+/- 3dB

 

 

 

Damping Factor

> 100

> 100

 

 

 

Input Sensitivity

200mV to 8V

200mV to 8V

 

 

 

Input Sensitivity Selection

Yes

Yes

Switch

 

 

 

 

 

Supply Voltage Range

9 to 16V

9 to 16V

 

 

 

Protection

Thermal, DC offset, short protection,

 

under-voltage

 

 

 

 

Amplifier Section

XTR2504

XTR5004

Terminal Wire Gauge

Power 4 AWG

Power 4 AWG

 

Remote 12 AWG

Remote 12 AWG

 

Ground 4 AWG

Ground 4 AWG

 

Speaker 12 AWG

Speaker 12 AWG

 

 

 

Input Impedance

20kΩ

20kΩ

 

 

 

Balanced Line Inputs

Yes

Yes

 

 

 

Dimensions (inches)

11..5”x 9..3”x 2..5”

14..25”x 9..3”x 2..5”

 

 

 

Crossover Section

 

 

 

 

 

High Pass Crossover

Continuously vari-

Continuously vari-

 

able (50-2 kHz)

able (50-2 kHz)

 

 

 

Low Pass Crossover

Continuously vari-

Continuously vari-

 

able (50-2 kHz)

able (50-2 kHz)

 

 

 

Bass Boost

0-18dB variable

0-18dB variable

 

 

 

*Continuous 4Ω load 20Hz to 20kHz, < 1% THD, with input voltage at 14..4 VDC..

**Continuous 2Ω load 20Hz to 20kHz, < 1% THD, with input voltage at 14..4 VDC..

© 2008 Directed Electronics. All rights reserved.

5

Image 6
Contents Amplifier Contents Introduction End Panel Layouts CEA Specifications Specifications Internal Crossover Configurations, Flat full range Signal Input and Output ConfigurationsLine Output Configurations Crossover SwitchAdjusting Bass Boost High-Pass CrossoverInfinite Baffle Subsonic is set at 20Hz Sealed Example High-Pass Set at 20Hz Sealed Example High-Pass Set at 30HzPower Connections Speaker Connections XTR2504 and XTR5004Four Channel Stereo Configuration Tri-Mode Six Channel Configuration Passenger Compartment General Precautions and Installation TipsChoosing Mounting Locations Trunk CompartmentTools of the Trade Step By Step Installation Testing the System Adjusting the Sound of the SystemAmplifier Visual Troubleshooting Amplifier Top Plate Troubleshooting Tips Symptom Probable Cause Action To TakeSymptom Probable Cause Directed Electronics. All rights reserved Français Disposition DES Panneaux LatérauxCEA Specifications Caractéristiques Techniques Réglages DE L’AMPLIFICATEUR Réglage du renforcement des graves Filtre passe-basFiltre passe-haut Réglage passe-haut à 20 Hz dans le cas d’un cais- son closRaccordement DE L’AMPLIFICATEUR Configuration à trois canaux Configuration tri-mode six canauxPrécautions générales et conseils d’installation Installation DE L’AMPLIFICATEURChoix des emplacements de montage HabitacleOutillage requis Installation pas à pas Réglage ET Résolution DES Problèmes Essai du systèmeRéglage du son du système Résolution visuelle des problèmes de l’amplificateur Plaque supérieure de l’amplificateur Conseils de dépannage Symptôme Cause probable InterventionFrançais Symptôme Cause probable Español Disposiciones DEL Panel DE ExtremoEspecificaciones DE LA CEA THD+NEspecificaciones Configuraciones DEL Amplificador Ajuste del refuerzo de bajos Crossover de pasabajasCrossover de pasaaltas Bafle infinito, filtro subsónico en 20 HzCableado DEL Amplificador Configuración en puente de dos canalesConfiguración estereofónica de cuatro canales Conexiones de altavoces del XTR2504 y del XTR5004Configuración de tres canales Configuración de modalidad triple de seis canalesCompartimiento de pasajeros Instalación DEL AmplificadorSelección de ubicaciones de montaje MaleteroHerramientas DEL Oficio Instalación paso a paso Configuración Y Detección Y Reparación DE Averías Prueba del sistemaDetección y reparación visual de averías del ampli- ficador Placa superior del amplificador Sugerencias de detección y reparación de averías Síntoma Causa probable Medidas a tomarEspañol Síntoma Causa probable Layout DER Endplatten Eingangsmodus Kanäle 3 und 4 Definition siehe PunktCEA-DATEN Technische Daten Verstärkereinstellungen Unendliche Schallwand, Subsonic auf 20 Hz einges- tellt Hochpass-CrossoverEinstellung des Bass-Boost Beispiel Geschlossenes Gehäuse, Hochpassfilter bei 20 HzStromanschlüsse für den XTR2504 und XTR5004 VerstärkerverkabelungBeispiel Geschlossenes Gehäuse, Hochpassfilter bei 30 Hz Lautsprecheranschlüsse XTR2504 und XTR5004Dreikanal-Konfiguration Zweikanal-BrückenkonfigurationVierkanal-Stereokonfiguration Dreimodus-SechskanalbetriebWahl der Einbaustelle VerstärkerinstallationAllgemeine Vorsichts- und Installationshinweise FahrgastraumWerkzeuge Schrittweise Installation Einstellung UND Problemlösung SystemtestSystemsound einstellen Visuelle Anzeige von Problemen mit dem Verstärker Obere Platte des Verstärkers Problemlösungen Symptom Mögliche Ursache LösungSymptom Mögliche Ursache LösungDirected Electronics. Alle Rechte vorbehalten Italiano Layout DEI Pannelli TerminaliSpecifiche CEA Dati Tecnici Impostazioni DELL’AMPLIFICATORE Configurazione dei segnali d’ingresso e di uscitaConfigurazioni delle uscite di linea Guadagno d’ingressoCrossover passa-basso Crossover passa-altoRegolazione dell’amplificazione dei bassi Cablaggio DELL’AMPLIFICATORE Configurazione a cablaggio in parallelo con due canaliConfigurazione stereo a quattro canali Connessioni per l’alimentazioneConfigurazione a tre canali Configurazione a sei canali in modalità triplaNstallazione DELL’AMPLIFICATORE Scelta del punto di installazionePrecauzioni generali e suggerimenti per l’installazione AbitacoloCorredo per l’installazione Procedura di installazione Impostazione E Soluzione DEI Problemi Prova dell’impiantoRegolazione dell’audio dell’impianto Spie dell’amplificatore Piastra superiore dell’amplificatore Soluzione dei problemi Sintomo Causa probabile Intervento necessarioItaliano Sintomo Causa probabile Layouts DOS Painéis Controle de Ganho canais 3 e 4 ver a definição no itemEspecificações DA CEA Especificações Ajustes do Amplificador Exemplo de caixa selada com passa-alta ajustado a 20 Hz Crossover passa-altaSonoflector subsônico infinito é ajustado a 20 Hz Exemplo de caixa selada com passa-alta ajustado a 30HzConexão DOS Cabos do Amplificador Configuração em ponte de dois canaisConfiguração estéreo de quatro canais Conexões elétricasConfiguração de três canais Configuração trimodal de seis canaisCabine de passageiros Instalação do AmplificadorEscolha de locais de instalação Porta-malasFerramentas Instalação passo a passo Ajuste E Resolução DE Problemas Como testar o sistemaComo ajustar o som do sistema Identificação visual de problemas com o amplifi- cador Placa superior do amplificador Sugestões para resolução de problemas Problema Provável causa Medida a ser tomadaInterno deste manual Directed Electronics. Todos os direitos reservados 100 Warranty

XTR5004, XTR2504 specifications

The Directed Audio XTR2504 and XTR5004 are premium amplifiers designed for audio enthusiasts seeking an exceptional listening experience. These models are part of Directed's XTR line, which is known for its innovative technology and high performance, catering to both car audio and home audio applications.

One of the main features of the XTR2504 is its compact design, which allows it to fit in a variety of installation locations without compromising on power. The amplifier is rated at 250 watts RMS, providing ample power to drive mid-range and high-frequency speakers. It boasts a 4-channel output configuration, making it suitable for multi-speaker setups and offering flexibility for system customization.

The XTR5004 takes performance a step further, delivering an impressive 500 watts RMS. This model is ideal for larger setups or for users who require additional power to energize larger speakers and subwoofers. Both models utilize high-efficiency class D amplification technology, which minimizes power consumption while maximizing output. This efficiency translates to less heat generation, allowing for prolonged use without the risk of overheating.

One of the standout technologies featured in these amplifiers is their advanced signal processing capabilities. Both the XTR2504 and XTR5004 come equipped with variable high-pass and low-pass filters, allowing users to tailor the output frequency range according to their specific needs. This feature is crucial for optimizing sound quality, ensuring that each speaker operates within its optimal range, leading to a clearer and more balanced audio experience.

The amplifiers also incorporate a robust thermal management system, including built-in protection mechanisms that prevent damage from overheating or short circuits. This attention to durability and reliability makes the XTR2504 and XTR5004 ideal choices for both competitive audio setups and casual listening environments.

Additional characteristics include a sleek, modern design featuring a durable chassis that can withstand the rigors of installation in car environments. The amplifiers feature high-quality RCA inputs and remote gain control options for user convenience.

In summary, the Directed Audio XTR2504 and XTR5004 amplifiers exemplify cutting-edge technology in the realm of audio performance. With their powerful output, efficient design, and customizable features, these models are designed to provide an immersive audio experience that will satisfy even the most discerning audiophiles.