Directed Audio XTR5004, XTR2504 Troubleshooting Tips, Symptom Probable Cause Action To Take

Page 19

Troubleshooting Tips

Symptom

Probable Cause

Action To Take

 

 

 

No output

 

 

 

 

 

 

Low or no remote turn-on

Check remote turn-on voltage at voltage amplifier and repair as needed..

 

 

 

 

Fuse blown

Check power wire's integrity and check for speaker shorts.. Fix as needed

 

 

and replace fuse..

 

 

 

 

Power wires not connected

Check power wire and ground connections and repair or replace as needed..

 

 

 

 

Audio input not connected..

Check RCA connections and repair or replace as needed..

 

 

 

 

Speaker wires not connected

Check speaker wires and repair or replace as needed..

 

 

 

 

Speaker are blown

Check system with known working speaker and repair or replace speakers as

 

 

needed..

 

 

Audio cycles on and off

 

 

 

 

 

Thermal protection engages when amplifier heat

Make sure there is proper ventilation for amplifier and improve ventilation

 

sink temperature exceeds 75º C (167º F)

as needed..

 

 

 

 

Loose or poor audio input

Check RCA connections and repair or replace as needed..

 

 

 

 

Loose power connections

Check power wires and ground connections and repair or replace as needed..

 

 

Distorted output

 

 

 

 

 

Amplifier level sensitivity set too high exceeding

Readjust gain.. Refer to the Adjusting the Sound of the System section of this

 

maximum capability of amplifier

manual for detailed instructions..

 

 

 

 

Impedance load to amplifier too low

Check speaker impedance load, if below 2Ω, rewire the speakers to achieve

 

 

higher impedance.

 

Shorted speaker wires

Check speaker wires and repair or replace as needed..

 

 

 

© 2008 Directed Electronics. All rights reserved.

18

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Amplifier Contents Introduction End Panel Layouts CEA Specifications Specifications Crossover Switch Signal Input and Output ConfigurationsLine Output Configurations Internal Crossover Configurations, Flat full rangeHigh-Pass Crossover Adjusting Bass BoostInfinite Baffle Subsonic is set at 20Hz Sealed Example High-Pass Set at 30Hz Sealed Example High-Pass Set at 20HzSpeaker Connections XTR2504 and XTR5004 Power ConnectionsFour Channel Stereo Configuration Tri-Mode Six Channel Configuration Trunk Compartment General Precautions and Installation TipsChoosing Mounting Locations Passenger CompartmentTools of the Trade Step By Step Installation Adjusting the Sound of the System Testing the SystemAmplifier Visual Troubleshooting Amplifier Top Plate Symptom Probable Cause Action To Take Troubleshooting TipsSymptom Probable Cause Directed Electronics. All rights reserved Disposition DES Panneaux Latéraux FrançaisCEA Specifications Caractéristiques Techniques Réglages DE L’AMPLIFICATEUR Réglage passe-haut à 20 Hz dans le cas d’un cais- son clos Filtre passe-basFiltre passe-haut Réglage du renforcement des gravesRaccordement DE L’AMPLIFICATEUR Configuration tri-mode six canaux Configuration à trois canauxHabitacle Installation DE L’AMPLIFICATEURChoix des emplacements de montage Précautions générales et conseils d’installationOutillage requis Installation pas à pas Essai du système Réglage ET Résolution DES ProblèmesRéglage du son du système Résolution visuelle des problèmes de l’amplificateur Plaque supérieure de l’amplificateur Symptôme Cause probable Intervention Conseils de dépannageFrançais Symptôme Cause probable Disposiciones DEL Panel DE Extremo EspañolTHD+N Especificaciones DE LA CEAEspecificaciones Configuraciones DEL Amplificador Bafle infinito, filtro subsónico en 20 Hz Crossover de pasabajasCrossover de pasaaltas Ajuste del refuerzo de bajosConexiones de altavoces del XTR2504 y del XTR5004 Configuración en puente de dos canalesConfiguración estereofónica de cuatro canales Cableado DEL AmplificadorConfiguración de modalidad triple de seis canales Configuración de tres canalesMaletero Instalación DEL AmplificadorSelección de ubicaciones de montaje Compartimiento de pasajerosHerramientas DEL Oficio Instalación paso a paso Prueba del sistema Configuración Y Detección Y Reparación DE AveríasDetección y reparación visual de averías del ampli- ficador Placa superior del amplificador Síntoma Causa probable Medidas a tomar Sugerencias de detección y reparación de averíasEspañol Síntoma Causa probable Eingangsmodus Kanäle 3 und 4 Definition siehe Punkt Layout DER EndplattenCEA-DATEN Technische Daten Verstärkereinstellungen Beispiel Geschlossenes Gehäuse, Hochpassfilter bei 20 Hz Hochpass-CrossoverEinstellung des Bass-Boost Unendliche Schallwand, Subsonic auf 20 Hz einges- telltLautsprecheranschlüsse XTR2504 und XTR5004 VerstärkerverkabelungBeispiel Geschlossenes Gehäuse, Hochpassfilter bei 30 Hz Stromanschlüsse für den XTR2504 und XTR5004Dreimodus-Sechskanalbetrieb Zweikanal-BrückenkonfigurationVierkanal-Stereokonfiguration Dreikanal-KonfigurationFahrgastraum VerstärkerinstallationAllgemeine Vorsichts- und Installationshinweise Wahl der EinbaustelleWerkzeuge Schrittweise Installation Systemtest Einstellung UND ProblemlösungSystemsound einstellen Visuelle Anzeige von Problemen mit dem Verstärker Obere Platte des Verstärkers Symptom Mögliche Ursache Lösung ProblemlösungenLösung Symptom Mögliche UrsacheDirected Electronics. Alle Rechte vorbehalten Layout DEI Pannelli Terminali ItalianoSpecifiche CEA Dati Tecnici Guadagno d’ingresso Configurazione dei segnali d’ingresso e di uscitaConfigurazioni delle uscite di linea Impostazioni DELL’AMPLIFICATORECrossover passa-alto Crossover passa-bassoRegolazione dell’amplificazione dei bassi Connessioni per l’alimentazione Configurazione a cablaggio in parallelo con due canaliConfigurazione stereo a quattro canali Cablaggio DELL’AMPLIFICATOREConfigurazione a sei canali in modalità tripla Configurazione a tre canaliAbitacolo Scelta del punto di installazionePrecauzioni generali e suggerimenti per l’installazione Nstallazione DELL’AMPLIFICATORECorredo per l’installazione Procedura di installazione Prova dell’impianto Impostazione E Soluzione DEI ProblemiRegolazione dell’audio dell’impianto Spie dell’amplificatore Piastra superiore dell’amplificatore Sintomo Causa probabile Intervento necessario Soluzione dei problemiItaliano Sintomo Causa probabile Controle de Ganho canais 3 e 4 ver a definição no item Layouts DOS PainéisEspecificações DA CEA Especificações Ajustes do Amplificador Exemplo de caixa selada com passa-alta ajustado a 30Hz Crossover passa-altaSonoflector subsônico infinito é ajustado a 20 Hz Exemplo de caixa selada com passa-alta ajustado a 20 HzConexões elétricas Configuração em ponte de dois canaisConfiguração estéreo de quatro canais Conexão DOS Cabos do AmplificadorConfiguração trimodal de seis canais Configuração de três canaisPorta-malas Instalação do AmplificadorEscolha de locais de instalação Cabine de passageirosFerramentas Instalação passo a passo Como testar o sistema Ajuste E Resolução DE ProblemasComo ajustar o som do sistema Identificação visual de problemas com o amplifi- cador Placa superior do amplificador Problema Provável causa Medida a ser tomada Sugestões para resolução de problemasInterno deste manual Directed Electronics. Todos os direitos reservados 100 Warranty

XTR5004, XTR2504 specifications

The Directed Audio XTR2504 and XTR5004 are premium amplifiers designed for audio enthusiasts seeking an exceptional listening experience. These models are part of Directed's XTR line, which is known for its innovative technology and high performance, catering to both car audio and home audio applications.

One of the main features of the XTR2504 is its compact design, which allows it to fit in a variety of installation locations without compromising on power. The amplifier is rated at 250 watts RMS, providing ample power to drive mid-range and high-frequency speakers. It boasts a 4-channel output configuration, making it suitable for multi-speaker setups and offering flexibility for system customization.

The XTR5004 takes performance a step further, delivering an impressive 500 watts RMS. This model is ideal for larger setups or for users who require additional power to energize larger speakers and subwoofers. Both models utilize high-efficiency class D amplification technology, which minimizes power consumption while maximizing output. This efficiency translates to less heat generation, allowing for prolonged use without the risk of overheating.

One of the standout technologies featured in these amplifiers is their advanced signal processing capabilities. Both the XTR2504 and XTR5004 come equipped with variable high-pass and low-pass filters, allowing users to tailor the output frequency range according to their specific needs. This feature is crucial for optimizing sound quality, ensuring that each speaker operates within its optimal range, leading to a clearer and more balanced audio experience.

The amplifiers also incorporate a robust thermal management system, including built-in protection mechanisms that prevent damage from overheating or short circuits. This attention to durability and reliability makes the XTR2504 and XTR5004 ideal choices for both competitive audio setups and casual listening environments.

Additional characteristics include a sleek, modern design featuring a durable chassis that can withstand the rigors of installation in car environments. The amplifiers feature high-quality RCA inputs and remote gain control options for user convenience.

In summary, the Directed Audio XTR2504 and XTR5004 amplifiers exemplify cutting-edge technology in the realm of audio performance. With their powerful output, efficient design, and customizable features, these models are designed to provide an immersive audio experience that will satisfy even the most discerning audiophiles.
Top Page Image Contents