Rockford Fosgate RFX9110, RFX9210G Installation Installation Considerations, Mounting Locations

Page 5

INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Volt/Ohm Meter

Wire strippers

Wire crimpers

Wire cutters

#2 Phillips screwdriver

Battery post wrench

Hand held drill w/assorted bits

1/8" diameter heatshrink tubing

Assorted connectors

Soldering iron

Solder

Heat gun

This section focuses on some of the vehicle considerations for installing your new Source Unit. Pre- planning your system layout and best wiring routes will save installation time. When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

!CAUTION: If you feel unsure about installing this system yourself, have it installed by a qualified technician.

!CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1.Be sure to carefully read and understand the instructions before attempting to install the Unit.

2.For safety, disconnect the negative lead from the battery prior to beginning the installation.

3.For easier assembly, we suggest you run all wires prior to mounting your Source Unit in place.

4.Route all of the RCA cables close together and away from any high current wires.

5.Use high quality connectors for a reliable installation and to minimize signal or power loss.

6.Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7.Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8.Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

9.ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18” (45.7 cm) of the battery terminal.

10.When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

MOUNTING LOCATIONS

The mounting position of your source unit will have a great effect on the performance of your in- dash CD Player. The source unit can be installed in a wide range of operating locations. However, care should be taken to ensure optimum performance.

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.

Instrument Panel

Mounting the source unit in the instrument panel provides optimum access. The source unit should be securely mounted using the “Standard Mount” or “ISO-DIN Mount” method to ensure optimum CD Player performance.

5

Image 5
Contents Source Units Introduction Table of ContentsPrecautions Source Unit and Optional CD Changer Safety InstructionsOperating Temperature Moisture CondensationIR Remote Controller PrecautionsContents of Carton Compact DiscsMounting Locations Installation Installation ConsiderationsEngine Compartment Instrument PanelWiring the System InstallationCenter Console Glove BoxStandard Mount InstallingISO-DIN Mount RemovalSource Unit Features Operation Basic Initial Setup Detachable Faceplate IR Remote Special FeaturesTo Detach the Faceplate To Attach the FaceplatePower ON/OFF Operation Basic Reset ButtonVolume KNOB/TONE Controls Setup OptionsOperation Basic Mode SelectionClock Operation MuteOperation Basic Punch Panel Display DefaultPanel Display Operation Tuner Selecting a BandAF/TP Mode Preset ButtonsOperation Tuner Selecting a Station Auto StoreBasic Operation Operation Tuner PTY ModeOperation CD Player To Play a CDTo Play Tracks at Random Advanced OperationTo Repeat a Track Forward/ReverseCD Changer Reset Direct Track AccessPause CD Magazine EjectOperation Title Programming Programmable Disc Title Memory Model 9210 OnlyOperation MP3 MP3 Player Operation Basic PlayingNegotiating the MP3 Directory Fast Forward/Fast Reverse Down ButtonMaximum Writing Speed and Bit Depth Programmable TitlingGeneral TroubleshootingTOC Error Servo ErrorRadiated Noises CD skipsEngine Noise CD Changer TroubleshootingError Magazine Eject IR Remote General 9110 9210 SpecificationsShip to Electronics Limited Warranty InformationTable DES Matières FrançaisTempérature de fonctionnement Consignes DE SécuritéCondensation de lhumidité Exposition à lenvironnementMesures DE Précaution Télécommande InfrarougeDisques Compacts Contenu DE LemballageEmplacements DE Montage Installation Considérations Concernant LinstallationCompartiment du moteur Tableau de bordConsole centrale Câblage DU SystèmeBoîte à gant Sous le tableau de bordInstallation ISO-DIN Installation StandardManchon Vis Attache arrière Panneau Garniture +20 Verrou Support de montageCaractéristiques DE Lappareil OFF PWR-commande à distance Allume et éteint lappareilFonctionnement DE Base Réglage Initial Fonctions spéciales de la télécommande infrarougeFaçade Démontable Pour démonter la façadeTélécommande Boutons DE Réglage DE VOLUME/TONALITÉFonctionnement DE Base Bouton DE Réinitialisation Interrupteur DE Mise SOUS/HORS TensionFonctionnement DE Base Sélection DE ModeUtilisation DE Lhorloge Réglage des heuresPanneau Daffichage Fonctionnement DE Base PunchPanneau Daffichage PAR Défaut Fonctionnement DU Tuner Sélection Dune BandeFonctionnement DU Tuner Sélection Dune Station Mode AF/TPBoutons DE Présélection Programmation DES Titres DE StationFonctionnement de base Fonctionnement DU Tuner Mode PTYFonctionnement DU Lecteur CD Éjection dun disqueLecture aléatoire des pistes Fonctionnement avancéRépétition dune piste Avance/RetourRéinitialisation du changeur de CD Direct Track Access Accès direct aux pistesChargement dun disque dans le magazine Chargement du magazine dans le changeur de CDSélection de disque Mode de changeur de CDPanneau daffichage Fonctionnement DE LA Programmation DES TitresFonctionnement DE MP3 Fonctionnement du lecteur MP3 Lecture de baseUtilisation du répertoire MP3 Avance/Retour rapide Bouton DownVitesse décriture et bits de profondeur maximum Titrage programmableDépannage GénéralitésChargement Erreur deErreur déjection Erreur servoErreur Erreur déjection du magazine Dépannage du changeur de CDBruit de moteur Erreur Télécommande infrarougeErreur de Focalisation Disque absentGénéralités 9110 9210 CaractéristiquesAmplificateurs Punch 2 ans Informations SUR LA Garantie LimitéeSources audio 1 an Haut-parleurs 1 an Tout autre modèle damplificateur 3 ansÍndice DE Materias IntroducciónPrecaución Unidad Fuente Y Cambiador DE DC Opcional Instrucciones DE SeguridadTemperatura de funcionamiento Condensación de humedadControl Remoto Infrarrojo PrecaucionesDiscos Compactos Contenido DE LA CajaLugares DE Montaje Instalación Consideraciones Para LA InstalaciónCompartimiento del motor Panel de instrumentosPanel central InstalaciónGuantera Debajo del tablero de instrumentosSoporte ISO-DIN Soporte EstándarManga Tornillo Correa trasera Tablero Adorno +20 Traba Soporte de fábrica Tornillo Tablero AdornoCaracterísticas DE LA Unidad Fuente Funcionamiento Básico Preparación Inicial Características especiales del remoto infrarrojoCara Frontal Desprendible Para desprender la cara frontalFuncionamiento Básico Botón DE Reinicio Botón DE VOLUMEN/CONTROLES DE TonoAlimentación DE Corriente APAGAR/PRENDER Opciones DE AjusteFuncionamiento DEL Reloj Funcionamiento BásicoSelección DE Modos Ajuste de las horasPresentación DE LA Pantalla Funcionamiento Básico PunchPresentación DEL Panel POR Omisión Funcionamiento Sintonizador Selección DE BandasBotones Para Preselecciones Funcionamiento Sintonizador Selección DE RadiodifusorasAlmacenamiento Automático Programación DE Títulos Para RadiodifusorasFuncionamiento Sintonizador Modo PTY Funcionamiento BásicoFuncionamiento Reproductor DE DC Para reproducir un DCPara tocar pistas al azar Funcionamiento avanzadoPara repetir una pista Adelanto/RetrocesoAcceso directo a la pista Pausar el DCReinicio del Cambiador de DC Carga del disco en el CargadorSelección de Discos Modo de Cambiador de DCPresentación del panel Funcionamiento Programación DE TítulosFuncionamiento MP3 Funcionamiento del reproductor de MP3 Reproducción básicaNavegación del directorio MP3 Adelanto Rápido/Reversa Rápida Botón DownTitulación Programable Estructura del DirectorioNo hay Solución DE ProblemasIluminación de ContraluzRuidos irradiados Error delServomecanismo Error Solución de problemas del cambiador de DCError Error de Carga Ruido del motorRemoto Infrarrojo General EspecificacionesAmplificadores Punch 2 años Enviar aElectronicsInformación Sobre LA Garantía Limitada Nota Nota Rockford Fosgate