Jensen owner manual Troubleshooting, VM9510 Specifications, Mechanical Errors

Troubleshooting

Mechanical Errors

If a mechanical error occurs while opening the TFT screen, the screen stops moving and beeps three times.

If a mechanical error occurs while closing the TFT screen, the screen beeps three times and returns to the previous position.

Problem	Cause	Corrective Action
No power to unit	Fuse(s) blown	Check/replace fuse(s) in vehicle fuse box
No sound can be heard or	Speakers are not wired correctly	Connect speaker harness; check speaker
the volume is low		wires
	Speaker wires shorting to chassis	Check splices, insulate all bare wires
	ground or to each other
	Fader or Balance incorrectly	Check audio settings
	adjusted
	AV1 or AV2 not wired correctly	Check wiring
Will not read disc	Disc is upside down	Insert disc right side up
	Disc is dirty	Clean/inspect disc
	Format not supported by player	Insert correct disc format
The sound “skips” during	Disc is dirty	Clean/inspect disc
disc play
	Receiver mount is not solid or	Check mounting and backstrap, tighten if
	backstrap is not secure	needed
DVD will not play on main	Parking brake not applied	Apply parking brake
screen
Remote control does not	Batteries are weak	Check/replace batteries
work
	Sunlight is interfering with	If sunroof is allowing too much light, close
	infrared sensor	it partially or fully.
		Close windows
The display is dark	Direct sunlight reflecting off	Close windows and/or sunroof
	screen
	Color/Brightness settings	Adjust Color/Brightness settings
	incorrect
Poor TV reception	Poor antenna reception	Park vehicle (It is difficult to receive a clear
		signal in a moving vehicle.)
		Install Diversity antenna
Front panel will not	Front panel not centered	Re-center left/right manual swivel
motorize back into unit		adjustment

VM9510

Specifications

CEA Power Ratings

Power Output: 18 watts RMS X 4 channels into 4-ohms @ < 1% THD+N

Signal to Noise Ratio: 70dBA below reference. (Reference: 1 watt, 4-ohms)

Dynamic Power: 36 watts @ 4-ohms x 4 channels

Frequency Response: 20Hz to 20kHz (-3dB), Audio/Video input used as source reference

Reference Supply Voltage: 14.4VDC

DVD/CD Player

Compatible formats: DVD-R, DVD-RW, CD-R, CD-RW, CDDA, MP3, SVCD and VCD

Signal to Noise Ratio: >90dBA

Frequency Response: 20Hz to 20kHz, -3dB

Channel Separation: > 60dB @ 1kHz

D/A Converter: 1 bit

Video

Format: NTSC

Output: 1Vp-p (75-ohm)

Input: 1Vp-p (75-ohm)

FM Tuner

Tuning Range: 87.5MHz - 107.9MHz

Mono Sensitivity (-30dB): 9dBf

Quieting Sensitivity (-50dB): 15dBf

Alternate Channel Selectivity: 70dB

Signal to Noise Ratio @ 1kHz: 58dB

Image Rejection: 60dB

Stereo Separation @ 1kHz: >30dB

Frequency Response: 50Hz - 12kHz, -3dB

AM Tuner

Tuning Range: 530kHz - 1720kHz

Sensitivity (-20dB): 30uV

Signal to Noise Ratio @ 1kHz: 50dB

Image Rejection: 60dB

Frequency Response: 50Hz - 2kHz, -3dB

Monitor

Screen Size: 7.0" (Measured diagonally), 16:9 Widescreen "6.3" (160mm) H X 4.0" (102mm) W

Screen Type: TFT Liquid Crystal Display (LCD) active matrix

Resolution:

-DVD player: 1.15 Mega pixel (Internal RGB Digital Interface), 800 (H) X 480 (W) X 3

-Composite video input: 384,000 pixels, 800 (H) X 480 (W)

-Pixel pitch 0.1905 mm X 0.1905 mm

Viewing angle:

-65 degrees left or right

-45 degrees up

-60 degrees down

General

Audio input impedance: 10k

Power Supply: 11 to 16VDC, negative ground

Fuse: 10 amp, ATO type

DIN chassis dimensions: 7" x 7" x 2" (178mm x 178mm x 50mm)

TV Tuner dimensions: 4 11/16” x 2 3/4” x 13/16” (119mm x 70mm x 21mm)

** Specifications subject to change without notice.

42