Motorola I580 Recommended Test Equipment and Tools, Recommended Programming Equipment

Page 105

ORDERING REPLACEMENT PARTS AND KITS: Recommended Test Equipment and Tools

A.6 Recommended Test Equipment and Tools

The following table lists the standard test equipment recommended for troubleshooting i580 units at the field level of service.

Table A-2. Recommended Test Equipment and Tools

Description

Part Number

 

 

Battery Eliminator, Regulated

NNTN5589A

 

 

Black Stick

SLN7223A

 

 

Cable, Audio Jack Test

NNTN5175A

 

 

Cable, SMA to N-Type RF

Contact Motorola

 

 

Communications System Analyzer

Motorola R-2660

 

 

Data Cable, RS-232 (Serial Port)

NKN6560A

 

 

Data Cable, USB

NKN6559A

 

 

Digital Volt-Ohm Meter

Keithly 2001 or eq.

 

 

Power Supply, 0-15VDC, 0-3A

S1348D

 

 

SIM Card, Reference

NTN9208

 

 

Torx Bit, T-4

Commercially available

 

 

Torx Bit, T-6

6680387A70

 

 

Torx Driver, calibrated

RSX4043

 

 

Wrist Strap, Static ground

NTN9812

 

 

A.7 Recommended Programming Equipment

The following tables list the programming equipment and software recommended for troubleshooting i580 units at the field level of service.

Table A-3. Recommended Programming Equipment

Name

Part Number

Description

 

 

 

Cable, Data, RS232

NKN6560A

Connects unit to the computer for

Cable, Data, USB

NKN6559A

monitoring the codeplug.

 

 

 

90

68P80401P05

Image 105
Contents IDEN Digital Multi-Service, Data-Capable Portable I580 Manual Revisions Safety and General Information Medical Devices Electro Magnetic Interference CompatibilityCleaning and Drying Considerations Accessory Safety InformationSafety and General Information Model Numbering System Model InformationGeneral Receiver Transmitter Model SpecificationsContents Chapter Basic Level Test Modes and Procedures Chapter Field Level Test Modes and Procedures Appendix a Ordering Replacement Parts and Kits Preface Who Should Use This ManualHow This Manual Is Organized Related Publications Conventions Used in This ManualIDEN Digital Modulation Technology OverviewSpectrum of iDEN Quad 16QAM RF Transmission Bursts IDEN Voice Compression TechnologyCalling Area Coverage Bluetooth Wireless System Global Positioning System GPS SectionMOTOtalk SIM Cards Removing and Inserting a SIM CardTo remove a SIM card Figure To insert a SIM card Figure Removing a SIM CardI580 Features FEATURES, ICONS, and IndicatorsMain Menu Icons Display IconsStatus Icons DISPLAYS, MESSAGES, and Alerts Power-Up SequenceSelf-Test Errors Power-Down SequenceSelf-Test Reset Errors MessagesService Messages Service MessagesAlert Tones Alert TonesAlert Tones Alert Tones Using the Optional Vibrate Function Vibrator SettingsTo set unit to vibrate for all calls From the main menu, select Settings 2-Way Radio Alert Type Reference Accessories Preparing for Basic Level TestingTest Equipment Reference UnitBasic Level Checks and Self Tests Reset ConditionCustomer Care Test ConditionsPreventive Maintenance Basic-Level Test ChecklistBasic-Level Test Checklist To clean the unit takes approximately 3 minutesSIM Card Swap Test Mechanical and Electrical ChecksShock and Pressure test time is approximately 3 minutes SIM Card Swap test time is approximately 5 minutesAccessory Swap test time is approximately 5 minutes Accessory Swap TestLockup Test Lockup Test time is approximately 6 minutesTesting the GPS Receiver Battery Connections TestBattery Connections test time is approximately 5 minutes To test the GPS ReceiverSelf-Test Procedures Voltage Recognition TestVoltage Recognition test time is approximately 4 minutes Programming Menu Settings Check Passcode TestPasscode test time is approximately 5 minutes Phone Calls Features From the main menu, select Settings Display/Info ContrastWay Radio Options Volume Features Security FeaturesPersonalize From the main menu, select Settings Security GPS PIN Call Performance Test Advanced FeaturesCall Performance test time is approximately 7 minutes Entering Debug Mode Basic Level Test Modes and ProceduresTo enter Debug/Trace Mode Test ModesDisplay Screens Trace Mode Display ScreensGPS Entering Test Mode Test Mode Test ProceduresTo enter Test Mode Audio Loopback TestDebug Check ESN and Imei Matching TestAudio Loopback test time is approximately 3 minutes ESN/IMEI Matching test time is approximately 6 minutesTo monitor the data in the unit 68P80401P05 Technician Test Procedures Programming the i580 Unit Connecting the Unit to the RSS WorkstationCodeplug Troubleshooting To access the codeplug Help topic in WindowsCodeplug Help Preparing Equipment for Testing Preparing for Field Level TestingConnecting an iDEN Unit to the R-2660 Using RSSTo connect the unit to the R-2660 Typical R-2660 SetupTo enter Initial Registration mode Operating the R-2660RF Zone Fields and Values Disassembly Sequence Flowchart Assembly/Disassembly ProceduresDisassembling and Reassembling the Unit Remove Battery Cover InstallRemove Remove Battery Remove Antenna Remove SIM CardPreparing for Field Level Testing Remove Antenna Remove Back Housing Remove Main Board, Keypad Procedure to remove flip assembly Remove Flip AssemblyPreparing for Field Level Testing Remove Flip Assembly Procedure to install flip assembly Install Flip AssemblyPreparing for Field Level Testing Install Flip Assembly I580 Component Parts List Exploded View and Parts ListI580 Exploded View Field Level Test Modes and Procedures Required Test Equipment Field-Level Test ChecklistDone Technical Tests Pass Fail Field-Level Test ChecklistRegistration/Call Test See the Strong Signal Environment sectionR-2660 Signal Quality Error SQE TestSee Entering Test Mode Press Menu, Edit TX Power TestPass Bit Error Rate BER TestPower-Up Test Keypad Test Use this test to check the audio portion of the unit Audio TestReset Reset TestTo perform the reset log test Reset Log TestModel Assembly MA Test Mode Test Use this test on a unit to check its GPS functionality GPS Global Positioning System Receiver TestYes Bluetooth Test This Page intentionally left blank Recommended Equipment Mechanical Parts Rework and RepairRecommended Tools Recommended SuppliesRework/Repair Requirements Components Identification Board PreparationRemoval Procedure Mechanical Parts Rework ProcedureLand Preparation Procedure Installation Procedure4 J600 RF Connector 6 J401 30 Pin Board-to-Flex Connector5 J752 Audio Jack 7 J400 80 Pin Board-to Flex Connector 8 M002 Simm Connector9 M105 Battery Contact SW-all Key/Switch 10 M2 2 Pin-Contact11 J753 Microphone Socket 13 D401 through D412 LED Customer Service Ordering Replacement Parts and KitsReplacement Parts Domestic OrdersTable A-1 Replacement KitsMid Rate Travel Chargers Bluetooth Accessories NNTN2344 NA Recommended Programming Equipment Recommended Test Equipment and ToolsTable A-2. Recommended Test Equipment and Tools Table A-3. Recommended Programming EquipmentTTY Table A-4. Recommended Software@68P80401P05@
Related manuals
Manual 222 pages 58.9 Kb