Motorola I580 service manual Preparing for Field Level Testing Remove Antenna

Page 66

PREPARING FOR FIELD LEVEL TESTING: Remove Antenna

2.Extend antenna whip fully.

3.Hold unit stationary while tugging at collar until antenna assembly releases.

4.Insert tweezers into the antenna housing port, grab the edge of antenna tube and pull it out.

7.11.2Install:

1.Carefully push antenna collar into position.

2.Insert antenna assembly with whip fully extended, contact toward interior of unit. Push firmly until fully seated.

3.Pull antenna whip in and out to check for correct operation. Reinsert T-4 screw and tighten clockwise to 0.5 in/lb.

4.Align and insert new valence plug. Must be flush with surface.

1

3

Figure 7-5.

68P80401P05

51

Image 66

Contents IDEN Digital Multi-Service, Data-Capable Portable I580 Manual Revisions Safety and General Information Electro Magnetic Interference Compatibility Medical DevicesAccessory Safety Information Cleaning and Drying ConsiderationsSafety and General Information Model Information Model Numbering SystemModel Specifications General Receiver TransmitterContents Chapter Basic Level Test Modes and Procedures Chapter Field Level Test Modes and Procedures Appendix a Ordering Replacement Parts and Kits Preface Who Should Use This ManualHow This Manual Is Organized Conventions Used in This Manual Related PublicationsOverview IDEN Digital Modulation TechnologySpectrum of iDEN Quad 16QAM IDEN Voice Compression Technology RF Transmission BurstsCalling Area Coverage Bluetooth Wireless System Global Positioning System GPS SectionMOTOtalk SIM Cards Removing and Inserting a SIM CardTo remove a SIM card Figure Removing a SIM Card To insert a SIM card FigureFEATURES, ICONS, and Indicators I580 FeaturesDisplay Icons Main Menu IconsStatus Icons Power-Up Sequence DISPLAYS, MESSAGES, and AlertsSelf-Test Reset Errors Power-Down SequenceSelf-Test Errors MessagesService Messages Service MessagesAlert Tones Alert TonesAlert Tones Alert Tones Using the Optional Vibrate Function Vibrator SettingsTo set unit to vibrate for all calls From the main menu, select Settings 2-Way Radio Alert Type Test Equipment Preparing for Basic Level TestingReference Accessories Reference UnitCustomer Care Reset ConditionBasic Level Checks and Self Tests Test ConditionsBasic-Level Test Checklist Basic-Level Test ChecklistPreventive Maintenance To clean the unit takes approximately 3 minutesShock and Pressure test time is approximately 3 minutes Mechanical and Electrical ChecksSIM Card Swap Test SIM Card Swap test time is approximately 5 minutesLockup Test Accessory Swap TestAccessory Swap test time is approximately 5 minutes Lockup Test time is approximately 6 minutesBattery Connections test time is approximately 5 minutes Battery Connections TestTesting the GPS Receiver To test the GPS ReceiverSelf-Test Procedures Voltage Recognition TestVoltage Recognition test time is approximately 4 minutes Programming Menu Settings Check Passcode TestPasscode test time is approximately 5 minutes From the main menu, select Settings Display/Info Contrast Phone Calls FeaturesWay Radio Options Volume Features Security FeaturesPersonalize From the main menu, select Settings Security GPS PIN Advanced Features Call Performance TestCall Performance test time is approximately 7 minutes To enter Debug/Trace Mode Basic Level Test Modes and ProceduresEntering Debug Mode Test ModesTrace Mode Display Screens Display ScreensGPS To enter Test Mode Test Mode Test ProceduresEntering Test Mode Audio Loopback TestAudio Loopback test time is approximately 3 minutes ESN and Imei Matching TestDebug Check ESN/IMEI Matching test time is approximately 6 minutesTo monitor the data in the unit 68P80401P05 Technician Test Procedures Connecting the Unit to the RSS Workstation Programming the i580 UnitCodeplug Troubleshooting To access the codeplug Help topic in WindowsCodeplug Help Preparing for Field Level Testing Preparing Equipment for TestingUsing RSS Connecting an iDEN Unit to the R-2660Typical R-2660 Setup To connect the unit to the R-2660To enter Initial Registration mode Operating the R-2660RF Zone Fields and Values Disassembly Sequence Flowchart Assembly/Disassembly ProceduresDisassembling and Reassembling the Unit Remove Battery Cover InstallRemove Remove Battery Remove SIM Card Remove AntennaPreparing for Field Level Testing Remove Antenna Remove Back Housing Remove Main Board, Keypad Remove Flip Assembly Procedure to remove flip assemblyPreparing for Field Level Testing Remove Flip Assembly Install Flip Assembly Procedure to install flip assemblyPreparing for Field Level Testing Install Flip Assembly Exploded View and Parts List I580 Component Parts ListI580 Exploded View Field Level Test Modes and Procedures Field-Level Test Checklist Required Test EquipmentField-Level Test Checklist Done Technical Tests Pass FailSee the Strong Signal Environment section Registration/Call TestSignal Quality Error SQE Test R-2660TX Power Test See Entering Test Mode Press Menu, EditBit Error Rate BER Test PassPower-Up Test Keypad Test Audio Test Use this test to check the audio portion of the unitReset Test ResetReset Log Test To perform the reset log testModel Assembly MA Test Mode Test GPS Global Positioning System Receiver Test Use this test on a unit to check its GPS functionalityYes Bluetooth Test This Page intentionally left blank Mechanical Parts Rework and Repair Recommended EquipmentRecommended Tools Recommended SuppliesRework/Repair Requirements Board Preparation Components IdentificationLand Preparation Procedure Mechanical Parts Rework ProcedureRemoval Procedure Installation Procedure4 J600 RF Connector 6 J401 30 Pin Board-to-Flex Connector5 J752 Audio Jack 7 J400 80 Pin Board-to Flex Connector 8 M002 Simm Connector9 M105 Battery Contact SW-all Key/Switch 10 M2 2 Pin-Contact11 J753 Microphone Socket 13 D401 through D412 LED Replacement Parts Ordering Replacement Parts and KitsCustomer Service Domestic OrdersReplacement Kits Table A-1Mid Rate Travel Chargers Bluetooth Accessories NNTN2344 NA Table A-2. Recommended Test Equipment and Tools Recommended Test Equipment and ToolsRecommended Programming Equipment Table A-3. Recommended Programming EquipmentTable A-4. Recommended Software TTY@68P80401P05@

Related manuals

Manual 222 pages 58.9 Kb