Grizzly G0695 owner manual Headstock Ram Movement, To move the ram inward or outward

Page 29

Headstock Ram

Movement

The headstock can be moved inward or outward along the ram.

Always lock the ram firmly in place after adjusting its position. If the headstock slips during milling operation, the spinning cutter could bind and break apart, causing serious personal injury or property damage.

Tools Needed	Qty
Hex Wrench 8mm	1
To move the ram inward or outward:

1.DISCONNECT MILL FROM POWER!

2.Loosen the three recessed cap screws, then tighten the two raised cap screws slightly to expand the clamp (see Figure 28).

Model G0695 (Mfg. Since 9/10)

Raised Cap Screws

Ram

Recessed Cap
Screws	Clamp
	Clamp

Figure 28. Location of cap screws for adjusting

ram movement.

3.Push or pull the headstock in the direction of desired ram movement.

4.Loosen the two raised cap screws to allow the clamp to close, then tighten the three recessed cap screws to tighten the clamp around the headstock tube.

-27-

Image 29

Contents Model G0695 VS Milling Machine With RAM Head Page Table of Contents Manual Accuracy IntroductionContact Info Machine DescriptionIdentification Machine Data Sheet Table Info Safety Instructions for Machinery SafetyWearing Proper APPAREL. Do not wear Hearing PROTECTION. Always wear hearSafety Instructions for Machinery Machine Care and Maintenance Additional Safety Instructions For MillsGlossary of Terms Circuit Requirements 220V Single-Phase OperationNeeded for Setup SetupUnpacking Description QtyInventory Figure Qty InventoryBefore cleaning, gather the following CleanupSite Considerations Mounting to Shop Floor Moving & Placing MillUsing Machine Mounts AssemblyBolting to Concrete Floors To assemble your millTest Run Step Spindle Break-InControl Panel OperationsBasic Controls Additional table travel controls Model G0695 Mfg. Since 9/10 Table ControlsDownfeed Controls Table Movement Operation OverviewLimit Stops LocksTo tilt the head Headstock TiltingTools Needed Qty Hex Bolt To rotate the turret Headstock Turret RotationTo move the ram inward or outward Headstock Ram MovementSetting Spindle Speed Setting Spindle SpeedCalculating Spindle Speed Cutting Speeds for High Speed Steel HSS Cutting ToolsLoading/Unloading Tooling Chip CharacteristicsLoading Tooling Unloading ToolingG1075-52-PC. Clamping Kit AccessoriesG9299-10 Yuasa-Type Rotary Table H8370-Power Feed for MillsG5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder Set H2689-R-8 Quick Change Collet SetG2861-Face Mill G4051-Carbide Insert for Face Mill G9765-9-PC. Ball End Mill SetG5684-R-8 Vertical Collet Rack G5758-Tilt xG5649-5-C Spin Index G1054-Dividing Head-BS-1Model G5679 Steel Parallel Set G5679-Steel Parallel SetCleaning Protecting MaintenanceSchedule LubricationQuill Gearing One-Shot OilerVertical Bevel Gears Lubricant Frequency QtyTo tension the V-belt Belt TensioningLeadscrews Motor & Electrical ServiceTroubleshooting Operation Disconnect Mill from Power Before Adjusting the Gibs Adjusting GibsTo replace the V-belt Adjusting Backlash Belt ReplacementPage Wiring Safety Instructions WiringWiring Diagram Electrical Components Control panel wiringBase, Column, & Knee Breakdown Description Base, Column, & Knee Parts ListHead Breakdown Head Parts List Motor & Ram Breakdown Motor & Ram Parts List Table Breakdown Table Parts List Label Placement Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY