Grizzly G0695 owner manual Identification

Page 5

		Identification
A		B		E
		C
		D
S		M		F
		M
	R	N		G
	R
		O
		L
		P		H
				H
	Q			I
		K		I
		K		J
		Front	Rear	J
			Rear

Figure 1. Model G0695 identification.

A.	Control Panel (refer to Page 19 for details)	K.	Base
B.	Motor 1⁜1⁄2 HP, 220V, 3-Phase	L.	Splash Pan
C.	V-Belt Belt Tension Lever and Lock Bolt	M.	Belt Access Plate
D.	Coarse Downfeed Handle	N.	Headstock Ram
E.	Turret	O.	X-Axis Handwheel
F.	Downfeed Selector	P.	Cross (Y-Axis) Feed Limit Stops
G.	Work Light 110V	Q.	Y-Axis Handwheel
H.	X-Axis Handwheel	R.	Longitudinal Limit Stops
I.	Z-Axis Crank Handle	S.	Fine Downfeed Handwheel

J.One-Shot Oiler

To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.

Model G0695 (Mfg. Since 9/10)

-3-

Image 5

Contents Model G0695 VS Milling Machine With RAM Head Page Table of Contents Manual Accuracy IntroductionContact Info Machine DescriptionIdentification Machine Data Sheet Table Info Safety Instructions for Machinery SafetyWearing Proper APPAREL. Do not wear Hearing PROTECTION. Always wear hearSafety Instructions for Machinery Machine Care and Maintenance Additional Safety Instructions For MillsGlossary of Terms Circuit Requirements 220V Single-Phase OperationNeeded for Setup SetupUnpacking Description QtyInventory Figure Qty InventoryBefore cleaning, gather the following CleanupSite Considerations Mounting to Shop Floor Moving & Placing MillUsing Machine Mounts AssemblyBolting to Concrete Floors To assemble your millTest Run Step Spindle Break-InControl Panel OperationsBasic Controls Additional table travel controls Model G0695 Mfg. Since 9/10 Table ControlsDownfeed Controls Table Movement Operation OverviewLimit Stops LocksTo tilt the head Headstock TiltingTools Needed Qty Hex Bolt To rotate the turret Headstock Turret RotationTo move the ram inward or outward Headstock Ram MovementSetting Spindle Speed Setting Spindle SpeedCalculating Spindle Speed Cutting Speeds for High Speed Steel HSS Cutting ToolsLoading/Unloading Tooling Chip CharacteristicsLoading Tooling Unloading ToolingG1075-52-PC. Clamping Kit AccessoriesG9299-10 Yuasa-Type Rotary Table H8370-Power Feed for MillsG5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder Set H2689-R-8 Quick Change Collet SetG2861-Face Mill G4051-Carbide Insert for Face Mill G9765-9-PC. Ball End Mill SetG5684-R-8 Vertical Collet Rack G5758-Tilt xG5649-5-C Spin Index G1054-Dividing Head-BS-1Model G5679 Steel Parallel Set G5679-Steel Parallel SetCleaning Protecting MaintenanceSchedule LubricationQuill Gearing One-Shot OilerVertical Bevel Gears Lubricant Frequency QtyTo tension the V-belt Belt TensioningLeadscrews Motor & Electrical ServiceTroubleshooting Operation Disconnect Mill from Power Before Adjusting the Gibs Adjusting GibsTo replace the V-belt Adjusting Backlash Belt ReplacementPage Wiring Safety Instructions WiringWiring Diagram Electrical Components Control panel wiringBase, Column, & Knee Breakdown Description Base, Column, & Knee Parts ListHead Breakdown Head Parts List Motor & Ram Breakdown Motor & Ram Parts List Table Breakdown Table Parts List Label Placement Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY