Grizzly G0695 owner manual Operation Overview, Table Movement

Page 24

Operation Overview

This overview gives you the basic process that hap- pens during an operation with this mill. Familiarize yourself with this process to better understand the remaining parts of the Operation section.

To complete a typical operation, the operator does the following:

1.Loosens the knee lock, and adjusts the table height to ensure there is sufficient room to install the tooling in the quill and the workpiece on the table.

2.Installs correct tooling for the task.

3.Mounts the workpiece securely to the table using a vise or clamps.

4.Selects the appropriate spindle speed for the workpiece and tooling.

5.Selects the direction the spindle will turn, based on the type of cut needed, using the direction switch.

6.Unlocks the X- and Y-axis table locks, then secures the Z-axis lock.

7.Wears safety glasses or a face shield.

8.Starts the machine.

9.Adjusts the spindle height.

10.For milling operations, uses the X-axis handwheel to move the table left-and-right and uses the Y-axis handwheel to move the table in-or-out, so the cutter removes material evenly from the workpiece.

For drilling operations, uses the coarse downfeed lever or fine downfeed handle to lower the tooling into the workpiece, then raises the tooling out of the workpiece.

11.Presses the STOP button to stop the spin- dle.

-22-

Table Movement

This mill table has three paths of movement con- trolled by the corresponding handwheels or crank (see Figure 17):

1.Left–right (X-axis)

2.In–out (Y-axis)

3.Up–down (Z-axis)

X-Axis

or Left & Right

Y-Axis or

In & Out

Z-Axis or

Up & Down

Figure 17. The three movement paths of the mill

table.

The graduated dials are marked in increments of 0.001", with a full revolution of the handwheel moving the table 0.125".

Model G0695 (Mfg. Since 9/10)

Image 24
Contents Model G0695 VS Milling Machine With RAM Head Page Table of Contents Introduction Manual AccuracyContact Info Machine DescriptionIdentification Machine Data Sheet Table Info Safety Safety Instructions for MachineryWearing Proper APPAREL. Do not wear Hearing PROTECTION. Always wear hearSafety Instructions for Machinery Additional Safety Instructions For Mills Machine Care and MaintenanceGlossary of Terms 220V Single-Phase Operation Circuit RequirementsSetup Needed for SetupUnpacking Description QtyInventory Inventory Figure QtyCleanup Before cleaning, gather the followingSite Considerations Moving & Placing Mill Mounting to Shop FloorAssembly Using Machine MountsBolting to Concrete Floors To assemble your millTest Run Spindle Break-In StepOperations Basic ControlsControl Panel Table Controls Additional table travel controls Model G0695 Mfg. Since 9/10Downfeed Controls Operation Overview Table MovementLocks Limit StopsHeadstock Tilting Tools Needed QtyTo tilt the head Hex Bolt Headstock Turret Rotation To rotate the turretHeadstock Ram Movement To move the ram inward or outwardSetting Spindle Speed Setting Spindle SpeedCalculating Spindle Speed Cutting Speeds for High Speed Steel HSS Cutting ToolsChip Characteristics Loading/Unloading ToolingLoading Tooling Unloading ToolingAccessories G1075-52-PC. Clamping KitH8370-Power Feed for Mills G9299-10 Yuasa-Type Rotary TableH2689-R-8 Quick Change Collet Set G5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder SetG2861-Face Mill G4051-Carbide Insert for Face Mill G9765-9-PC. Ball End Mill SetG5758-Tilt x G5684-R-8 Vertical Collet RackG5649-5-C Spin Index G1054-Dividing Head-BS-1G5679-Steel Parallel Set Model G5679 Steel Parallel SetMaintenance Cleaning ProtectingSchedule LubricationOne-Shot Oiler Quill GearingVertical Bevel Gears Lubricant Frequency QtyBelt Tensioning LeadscrewsTo tension the V-belt Service TroubleshootingMotor & Electrical Operation Adjusting Gibs Disconnect Mill from Power Before Adjusting the GibsAdjusting Backlash Belt Replacement To replace the V-beltPage Wiring Wiring Safety InstructionsWiring Diagram Control panel wiring Electrical ComponentsBase, Column, & Knee Breakdown Base, Column, & Knee Parts List DescriptionHead Breakdown Head Parts List Motor & Ram Breakdown Motor & Ram Parts List Table Breakdown Table Parts List Label Placement Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY