Grizzly G0695 owner manual Hex Bolt

Page 27

Always get an assistant to help you tilt the headstock or tighten the headstock lock nuts during the following steps. The head- stock is very heavy and may be difficult to control once it is tilted past 45ºR or 45ºL.

If you do not pay attention, it can flip over, causing serious personal injury and pos- sible machine damage.

5.Determine which of the two hex bolts that lock the headstock vertically is loose.

6.Tighten the locking hex nut on the opposite side of the headstock to secure it.

7.Remove the hex nut and flat washer from the hex bolt that is loose.

8.While an assistant holds the machine motor, loosen the locking hex nut on the opposite side, then push the loose hex bolt back into the headstock (see Figure 25) until your assistant can tilt the headstock back to the vertical position.

Note: The head of the hex bolt must re- engage with the T-slot on the inside of the headstock for the headstock to move.

9.Reinstall the flat washer and hex nut you removed earlier.

Always lock the head firmly in place after adjusting the tilt. Unexpected movement of the head during operations could cause the cutter to bind with the workpiece causing damage to the cutter and workpiece, and possible personal injury.

Hex Bolt

Figure 25. Pushing hex bolt back into

headstock.

Model G0695 (Mfg. Since 9/10)

-25-

Image 27

Contents Model G0695 VS Milling Machine With RAM Head Page Table of Contents Machine Description IntroductionManual Accuracy Contact InfoIdentification Machine Data Sheet Table Info Hearing PROTECTION. Always wear hear SafetySafety Instructions for Machinery Wearing Proper APPAREL. Do not wearSafety Instructions for Machinery Machine Care and Maintenance Additional Safety Instructions For MillsGlossary of Terms Circuit Requirements 220V Single-Phase OperationDescription Qty SetupNeeded for Setup UnpackingInventory Figure Qty InventoryBefore cleaning, gather the following CleanupSite Considerations Mounting to Shop Floor Moving & Placing MillTo assemble your mill AssemblyUsing Machine Mounts Bolting to Concrete FloorsTest Run Step Spindle Break-InOperations Basic ControlsControl Panel Additional table travel controls Model G0695 Mfg. Since 9/10 Table ControlsDownfeed Controls Table Movement Operation OverviewLimit Stops LocksHeadstock Tilting Tools Needed QtyTo tilt the head Hex Bolt To rotate the turret Headstock Turret RotationTo move the ram inward or outward Headstock Ram MovementCutting Speeds for High Speed Steel HSS Cutting Tools Setting Spindle SpeedSetting Spindle Speed Calculating Spindle SpeedUnloading Tooling Chip CharacteristicsLoading/Unloading Tooling Loading ToolingG1075-52-PC. Clamping Kit AccessoriesG9299-10 Yuasa-Type Rotary Table H8370-Power Feed for MillsG9765-9-PC. Ball End Mill Set H2689-R-8 Quick Change Collet SetG5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder Set G2861-Face Mill G4051-Carbide Insert for Face MillG1054-Dividing Head-BS-1 G5758-Tilt xG5684-R-8 Vertical Collet Rack G5649-5-C Spin IndexModel G5679 Steel Parallel Set G5679-Steel Parallel SetLubrication MaintenanceCleaning Protecting ScheduleLubricant Frequency Qty One-Shot OilerQuill Gearing Vertical Bevel GearsBelt Tensioning LeadscrewsTo tension the V-belt Service TroubleshootingMotor & Electrical Operation Disconnect Mill from Power Before Adjusting the Gibs Adjusting GibsTo replace the V-belt Adjusting Backlash Belt ReplacementPage Wiring Safety Instructions WiringWiring Diagram Electrical Components Control panel wiringBase, Column, & Knee Breakdown Description Base, Column, & Knee Parts ListHead Breakdown Head Parts List Motor & Ram Breakdown Motor & Ram Parts List Table Breakdown Table Parts List Label Placement Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY