Grizzly G0695 Safety Instructions for Machinery, Wearing Proper APPAREL. Do not wear

Page 8

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

 

 

WILL result in death or serious injury.

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

COULD result in death or serious injury.

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

MAY result in minor or moderate injury. It may also be used to alert

 

 

 

 

against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about

proper operation of the machine.

 

 

 

 

 

 

Safety Instructions for Machinery

 

 

 

 

 

 

 

 

 

Safety Instructions for Machinery

 

 

OWNER’S MANUAL. Read and understand

WEARING PROPER APPAREL. Do not wear

 

 

this owner’s manual BEFORE using machine.

clothing, apparel, or jewelry that can become

 

 

Untrained users can be seriously hurt.

entangled in moving parts. Always tie back or

 

 

 

cover long hair. Wear non-slip footwear to avoid

 

 

EYE PROTECTION. Always wear ANSI-

accidental slips which could cause a loss of

 

 

approved safety glasses or a face shield when

workpiece control.

 

 

operating or observing machinery. to reduce

HEARING PROTECTION. Always wear hear-

 

 

the risk of eye injury or blindness from fly-

 

 

ing particles Everyday eyeglasses are not

ing protection when operating or observiing loud

 

 

approved safety glasses.

machinery. Extended exposure to this noise

 

 

 

without hearing protection can cause permanent

 

 

HAzARDOUS DUST. Dust created while using

hearing loss.

 

 

machinery may cause cancer, birth defects,

MENTAL ALERTNESS. Be mentally alert when

 

 

or long-term respiratory damage. Be aware of

 

 

running machinery. Never operate under the

 

 

dust hazards associated with each workpiece

 

 

influence of drugs or alcohol, when tired, or when

 

 

material, and always wear a NIOSH-approved

 

 

distracted.

 

 

respirator to reduce your risk.

 

 

 

 

 

 

 

 

 

 

 

 

-6-

 

 

Model G0695 (Mfg. Since 9/10)

Image 8
Contents Model G0695 VS Milling Machine With RAM Head Page Table of Contents Introduction Manual AccuracyContact Info Machine DescriptionIdentification Machine Data Sheet Table Info Safety Safety Instructions for MachineryWearing Proper APPAREL. Do not wear Hearing PROTECTION. Always wear hearSafety Instructions for Machinery Additional Safety Instructions For Mills Machine Care and MaintenanceGlossary of Terms 220V Single-Phase Operation Circuit RequirementsSetup Needed for SetupUnpacking Description QtyInventory Inventory Figure QtyCleanup Before cleaning, gather the followingSite Considerations Moving & Placing Mill Mounting to Shop FloorAssembly Using Machine MountsBolting to Concrete Floors To assemble your millTest Run Spindle Break-In StepControl Panel OperationsBasic Controls Table Controls Additional table travel controls Model G0695 Mfg. Since 9/10Downfeed Controls Operation Overview Table MovementLocks Limit StopsTo tilt the head Headstock TiltingTools Needed Qty Hex Bolt Headstock Turret Rotation To rotate the turretHeadstock Ram Movement To move the ram inward or outwardSetting Spindle Speed Setting Spindle SpeedCalculating Spindle Speed Cutting Speeds for High Speed Steel HSS Cutting ToolsChip Characteristics Loading/Unloading ToolingLoading Tooling Unloading ToolingAccessories G1075-52-PC. Clamping KitH8370-Power Feed for Mills G9299-10 Yuasa-Type Rotary TableH2689-R-8 Quick Change Collet Set G5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder SetG2861-Face Mill G4051-Carbide Insert for Face Mill G9765-9-PC. Ball End Mill SetG5758-Tilt x G5684-R-8 Vertical Collet RackG5649-5-C Spin Index G1054-Dividing Head-BS-1G5679-Steel Parallel Set Model G5679 Steel Parallel SetMaintenance Cleaning ProtectingSchedule LubricationOne-Shot Oiler Quill GearingVertical Bevel Gears Lubricant Frequency QtyTo tension the V-belt Belt TensioningLeadscrews Motor & Electrical ServiceTroubleshooting Operation Adjusting Gibs Disconnect Mill from Power Before Adjusting the GibsAdjusting Backlash Belt Replacement To replace the V-beltPage Wiring Wiring Safety InstructionsWiring Diagram Control panel wiring Electrical ComponentsBase, Column, & Knee Breakdown Base, Column, & Knee Parts List DescriptionHead Breakdown Head Parts List Motor & Ram Breakdown Motor & Ram Parts List Table Breakdown Table Parts List Label Placement Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY