Diamondback 1190 Sr manual Strength Program

Page 29

1190SROM 9/22/06 1:51 PM Page 31

Workout Programs, continued

STRENGTH PROGRAM

Getting Started

The Strength program gradually increases the workload over time. This will strengthen not only your heart, but also the major muscle groups which are doing the work.

Beginning the Program

Start pedaling the unit. The message window will scroll a message “SELECT A PRO- GRAM”.

•Press the Classic Programs key until the Strength program LED indicator lights up.

Accepting Default values or Entering the program setting mode

When the message display flashes, “STRENGTH”, it indicates you are about to select the Strength program. The message display will scroll “PRESS ENTER TO ADJUST OR START TO BEGIN”.

•Press “START” key to accept current default values and begin Strength program workout.

o Default time = 30 minutes

•Or press “ENTER” key to enter program setup mode. The message display will bring you through the program setup step by step as below:

Entering Age

1.If ENTER key is pressed, the message window will flash once, “ENTER YOUR AGE”, then “AGE = XX” will start blinking.

2.Press “UP/DOWN” key to adjust the age.

3.After age is adjusted, then press “ENTER” key to accept.

Entering Weight

1.If ENTER key is pressed, the message window will flash once, “ENTER YOUR WEIGHT”, then “WEIGHT = XX” will start blinking.

2.Press “UP/DOWN” key to adjust the weight.

3.After weight is adjusted, then press “ENTER” key to accept.

Entering Program Time1190 Series

1.If ENTER key is pressed, the message window will flash once, “ENTER PROGRAM TIME”, then “TIME = 30 MIN” will start blinking.

2.Pressing “UP/DOWN” key to adjust the time. When the time setting reaches 60 minutes, the display will show “TIME = 1HR 00MIN”.

3.After time is adjusted, the message window will display “SET UP COMPLETED” “PRESS START TO BEGIN”. You may press the “START” key to begin this program.

Note: You may press the START key at any time during program setup to skip the adjust- ment and begin your workout. By doing so, the console will use default value of age and weight for %HR and calories burned calculations.

During the Program

Display

•Once the program is started, the message window will display the workout data of “Time, Intensity Level, Watts, and Calories”.

PROGRAM

PROFILE

1190 Sr Owner’s Manual

29

 

 

Page 28 Page 30
Image 29
Page 28 Page 30
Contents 1190SROM 9/22/06 151 PM Shipping Materials To Activate WarrantyPurchaser’s Reference Information Table of Contents Introduction Figure a Safety Instructions and WarningsAssembly Drawing Tools Required Assembly InstructionsRear Stabilizer Bar Console Mast & HandlebarSeat & Seat Back Rear HandlebarSeat Back Cover Pedal AssemblyExercise guidelines BMI = weight lb ÷ height2 in xGood health is an exercise in common sense Heart rate is an important key to your exerciseMaximum Heart Rate & Training Zone Get a smart start on exercising Quantity & QualityHeart Rate Monitoring Devices How to Wear Your Sensor/ TransmitterPulse Hand Grips Standard Chest Strap StandardHeart Rate Monitoring Devices Glossary of Terms Default valuesConsole Console Layout and Controls Function Keys Basic Operation Basic Operation O L D O W N Workout ProgramsR M U P R K O U T S U M M a R Y Ending the Cool DownI C K S T a R T A S S I C P R O G R a M S Random Program Workout Programs Interval Program Program ProfileHill Climb Program Workout Programs Strength Program I N T E R a C T I V E P R O G R a M S Workout Programs Heart Rate Interval Program Workout Programs Fatburner Program Workout Programs Cardio Program Workout Programs Workout Programs Maintenance What is Covered Domestic warranty InformationWarranty voided if Diamondback Fitness, Inc Diamondback Fitness Warranty Card Warranty cardCamarillo Ranch Road Camarillo, CA
Top Page Image Contents