Gold's Gym GGCCBE8057.0 manual

Page 25

47.Wrap the High Cable (81) over a Large Pulley (165). Attach the Large Pulley to the Swivel Bracket (31) with an M10 x 55mm Bolt (127), two M10 Washers (148), two M10 x 6.5mm Spacers (151), and an M10 Nylon Locknut (153).

Tighten the Cable Eyelet (174) as far as possible onto the end of the High Cable (81). Then, tighten the M8 Jam Nut (177) against the Cable Eyelet.

48.Identify the Rear Cable (94). Press the Weight Carriage Block (100) into the Weight Carriage (19). Insert one end of the Rear Cable into the the center of the Weight Carriage Block. Attach the Cable and the Weight Carriage Block to the Weight Carriage with an M10 x 65mm Bolt (137), two M10 Washers (148), two M10 x 20mm Spacers (150), and an M10 Nylon Locknut (153).

49.Route the Rear Cable (94) through the Weight Carriage Frame (18) as shown. Insert a Small Pulley (74) into the slot in the Weight Carriage Frame. Then, insert another Small Pulley (74). Attach each Small Pulley with an M10 x 55mm Bolt (127), two M10 Washers (148), two M10 x 6.5mm Spacers (151), and an M10 Nylon Locknut (153).

47
153
148
151
31
81		148	127
81	165		127
	165
177	174
	174
48
				94
	153	150		100
	148			150
	148			148
				148
		19		137
		19
49		74
		74
153	151		94
153	151		Slot
			Slot
148			18
148	151		151
			151

			148	127

25

Image 25

Contents Model No. GGCCBE8057.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Right Side Before YOU BeginLeft Side Part Identification Chart Page Make Assembly Easier AssemblyDo not tighten the Screws yet Nylon Locknut yet M10 Washers 148. Tighten the Screws used in steps 1153 148 155 Grease 123 Opening 124 122 170 172 154 Page 122 Large Hole Holes 180 Thick 131 End Posts Screws yet 115 109 112 153 Hole 148 151 127 Page Page En the Screw the Right Arm must pivot easily Attach the other Swivel Bracket not shown in the same way Attach the other Barbell Adapter not shown in the same wayScrew the Tether must rotate easily Cable in the groove of the V-pulley Sure that the Cable Trap is oriented to holdOriented to hold the Cable in the groove Pulley Locknut 153. Make sure that the Cable Trap isIdentify the High Cable 81. Feed the Cable 153 153 See the inset drawing. Insert the Cabling Rod Page Trap and the Half Pulley Guards are oriented as shown 153 140 148 151 127 125 Pulley Guards are oriented as shown Adjusting the Seat and Backrest AdjustmentAttaching the Curl PAD Attaching the Curl BARUsing the Weight Rests and the Weight Spotters Using the LEG LeverAdjust the right Barbell Spotter not shown in the same way Moving the Barbell SpottersAdjusting the Arms Using the Locking BARAdding Weights to the Barbell or the Weight Carriage Arm 22 in the same wayAttaching the Accessories to the LOW Pulley Station Attaching the Accessories to the High Pulley StationTightening the Cables MaintenanceHigh Cable Cable DiagramRear Cable Low CableExercise Guidelines Cooling Down Muscle ChartStaying Motivated Aerobic Exercise Weight Sets Reps Thursday Exercise Weight Sets RepsFriday Qty Description Part LIST-Model No. GGCCBE8057.0111 Exploded Drawing A-Model No. GGCCBE8057.0 R0707A Exploded Drawing B-Model No. GGCCBE8057.0 R0707A Exploded Drawing C-Model No. GGCCBE8057.0 R0707A Exploded Drawing D-Model No. GGCCBE8057.0 R0707A Limited Warranty Ordering Replacement Parts